Bogdan Kozik

Bogdan Kozik

Auto-generated profile, based on publicly available information

Bogdan Kozik

Department od Machine Design, The Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, Al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2023 in Advances in Science and Technology Research Journal
Verified
Journal Article
Open access
JBJacek Bernaczek
Jacek Bernaczek
MDMariusz Dębski
Mariusz Dębski
MGMałgorzata Gontarz
Małgorzata Gontarz
RGRoman Grygoruk
Roman Grygoruk
Jerzy JózwikJerzy Józwik
Jerzy Józwik
PMPiotr Mikulski
Piotr Mikulski
The purpose of the undertaken research work is to analyze the torsional strength of standard samples with a circular cross-section, produced additively using the SLS (Selective Laser Sintering) technique – sintering PA2200 polyamide powders. The studies conducted so far have not included a...

26 May 2025 in Polimery
Verified
Journal Article
Open access
PDF file
BKBogdan Kozik
Bogdan Kozik
JPJadwiga Pisula
Jadwiga Pisula
MDMariusz Dębski
Mariusz Dębski
TDTomasz Dziubek
Tomasz Dziubek
The durability of cylindrical spur gears made of ABS and PU manufactured using the FDM (Fused deposition modeling) additive method and vacuum casting was investigated. The tests were carried out for pairs of gears with an involute profile for three values of the profile angle: 20, 25 and 30° to determine the effect of the profile angle on the gear operation time. The effect of running-in on gear durability was also assessed.

16 December 2024 in Polimery
Verified
Journal Article
Open access
PDF file
MDMariusz Dębski
Mariusz Dębski
PNPiotr Nieslony
Piotr Nieslony
BKBogdan Kozik
Bogdan Kozik
JPJadwiga Pisula
Jadwiga Pisula
Opracowano hybrydową technologię wytwarzania części z materiałów polimerowych (ABS, PLA), łączącą metodę wytłaczania warstwowego i odlewania pod obniżonym ciśnieniem. Formę silikonową (stosowaną w metodzie odlewania ciśnieniowego) zastąpiono cienkościenną formą (o geometrii wytwarzanego elementu) wykonaną metodą wytłaczania warstwowego. Następnie w procesie odlewania próżniowego forma ta została wypełniona żywicą poliuretanową utwardzaną chemicznie. Zbadano właściwości mechaniczne przy rozciąganiu i zginaniu opracowanych modeli. Potwierdzono możliwość zmniejszenia anizotropii właściwości mechanicznych części wytwarzanych metodą przyrostową.

26 May 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
MDMariusz Dębski
Mariusz Dębski
Grzegorz BudzikGrzegorz Budzik
Grzegorz Budzik
AMAdam Marciniec
Adam Marciniec
BKBogdan Kozik
Bogdan Kozik
ŁPŁukasz Przeszłowski
Łukasz Przeszłowski
PNPiotr Niesłony
Piotr Niesłony
This paper presents a methodology for the quasi-static measurement of the failure torque of polymer gear pairs manufactured using additive manufacturing technologies. A dedicated test method and measurement rig were developed to enable testing of gear pairs subjected to torque loading under quasi-static conditions. The method is based on continuous recording of torque and angular displacement, while the failure torque is identified as the first local maximum of the torque–angle characteristic preceding a rapid loss of load-carrying capacity. Gear pairs manufactured from two polymer materials were investigated: PLA produced using the FFF technology and the RGD720 photopolymer produced using the PolyJet technology. Two design variants of the driven gear were analysed: a reference variant with a hub of constant axial cross-section and a solid load-bearing web, and a modified variant incorporating a thin-walled web and reinforcing ribs. This approach made it possible to assess the influence of modifications to the hub and gear web geometry on the maximum transmitted torque and the failure mechanism. The obtained results showed that modifying the gear geometry reduces its load-carrying capacity, with the extent of this reduction depending on the material and manufacturing technology. For PLA gears, lightweighting of the web reduced the mean failure torque from 245.9 Nm to 214.3 Nm, whereas for RGD720 gears it decreased from 199.8 Nm to 139.0 Nm. Different failure modes were observed: PLA gears failed locally at the teeth, whereas RGD720 gears showed brittle global cracking, especially in the lightweight variant.