Shinji Koganezawa

Shinji Koganezawa

Auto-generated profile, based on publicly available information

Shinji Koganezawa

Department of Mechanical Engineering, Kansai University, Suita, Japan

Research Focus & Metrics

Academic Career Length

31Years (1996-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 1996 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
KAK. Aruga
K. Aruga
YKY. Kuroba
Y. Kuroba
SKS. Koganezawa
S. Koganezawa
TYT. Yamada
T. Yamada
YNYuya Nagasawa
Yuya Nagasawa
YKY. Komura
Y. Komura

13 March 2024 in Lubricants
Verified
Journal Article
Open access
PDF file
QLQianru Li
Qianru Li
Renguo LURenguo LU
Renguo LU
HTHiroshi Tani
Hiroshi Tani
SKShouhei Kawada
Shouhei Kawada
SKShinji Koganezawa
Shinji Koganezawa
PCPeihong Cong
Peihong Cong
Tribofilms, resulting from tribochemical reactions involving lubricants, additives, and metal surfaces, are pivotal in reducing friction, preventing adhesion, and minimizing wear. This study investigates the tribological characteristics of textured surfaces in boundary lubrication, emphasizing the impact of surface texturing on tribofilm formation. Untextured surfaces manifest high friction coefficients and low wear owing to the development of thick tribofilms. However, debris accumulation impedes further tribochemical reactions, necessitating more energy for sliding and resulting in higher friction coefficients. Additionally, molybdenum dialkyl dithiocarbamate-derived MoS2 oxidation diminishes the expected lubrication effect. Textured surfaces exhibit lower friction coefficients and higher wear because the structure aids debris removal, promoting the formation of thinner tribofilms. Despite increased wear from solid-to-solid contact, textured surfaces facilitate an early fluid lubrication transition and enhance cavitation capacity, leading to reduced friction coefficients. We also consider the impact of sliding direction angles on friction coefficients, revealing that lower angles parallel to the grooves heighten friction, whereas higher angles enhance cavitation capacity. Unexpectedly, a 90° sliding direction angle increases the friction coefficients, attributed to MoS2 distribution in the tribofilms. These results provide crucial insights for optimizing lubrication strategies and enhancing wear resistance in boundary lubrication scenarios.

30 May 2018 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
SKShinji Koganezawa
Shinji Koganezawa
STShotaro Tsuda
Shotaro Tsuda
HTHiroshi Tani
Hiroshi Tani
RLRenguo Lu
Renguo Lu
NTNorio Tagawa
Norio Tagawa
In this paper, we applied the Hilbert-Huang transform (HHT) to the time series of the torque exerted on the carriage arm of a hard disk drive, which was calculated using the finite-element analysis. Then, a Fourier transform (FT) was implemented to perform frequency analysis; the results were subsequently compared with the HHT results. A comparison of both spectra revealed the superior ability of HHT to perform frequency analysis of flow phenomena via disturbance torque analysis. Furthermore, the HHT results confirmed that to achieve more precise head positioning, it is necessary to decrease torque fluctuations induced by the non-stationary phenomena that are not always observed in the power spectrum obtained via the FT analysis, such as vortex shedding around an arm.

1 January 2022 in Journal of Advanced Mechanical Design, Systems, and Manufacturing
Verified
Journal Article
Open access
PDF file
SKShinji Koganezawa
Shinji Koganezawa
TITomotake Ishii
Tomotake Ishii
HTHiroshi Tani
Hiroshi Tani
RLRenguo Lu
Renguo Lu
NTNorio Tagawa
Norio Tagawa
Previously, we proposed a self-powered vibration-based structural health monitoring system for diagnosing the structural soundness of entire bridges to screen bridges requiring detailed inspection. The core part of the system is the vibration-sensing device that is in the developing phase. This part relies on the Villari effect of magnetostrictive materials. In particular, the vibration-sensing device is a dual-use device that can serve as a vibration sensor and a power generator. This paper describes the design and evaluation results of the device’s performance. Galfenol, a typical magnetostrictive material, was used. Therefore, we first investigate the relationship between the magnetic flux density variation and the compression stress with different bias magnetic fields applied to the Galfenol rod. Moreover, an adequate range of the bias magnetic field was determined to maximize the power-generation performance and sensitivity of vibration. Subsequently, the prototype of the vibration-sensing device was designed and built, and a field test was conducted. The experimental results confirmed that the device works as a vibration sensor with high resolution. The device accurately detected the natural frequency of a bridge, even when subjected to the intermittent load of passing cars. The device generated 30.3 mJ in an hour even though it is a small-sized non-resonant power generator. With such generated energy, diagnosing the structural health at least once every two days can be executed with the developed device.

10 December 2019 in Lubricants
Verified
Journal Article
Open access
PDF file
Renguo LURenguo LU
Renguo LU
MMMasaya Morimoto
Masaya Morimoto
HTHiroshi Tani
Hiroshi Tani
NTNorio Tagawa
Norio Tagawa
SKShinji Koganezawa
Shinji Koganezawa
Lubricants that are used in miniaturized moving mechanical components generally serve under severe conditions, such as high temperature, high speed, and high load. Although alkyldiphenylethers (ADEs) are used as base oils for high-temperature greases, their tribological properties remain unclear. This study investigated the influence of the alkyl chains on the tribological properties of ADEs. Longer and more attached alkyl chains decreased the friction coefficient of ADEs under both reciprocating and continuous sliding conditions. Wear was found to be independent of the alkyl chain under reciprocating sliding conditions due to abrasion being caused by debris that was not readily removed. ADEs showed good anti-wear properties when used as either a lubricant or an additive under continuous sliding conditions. Much smoother surfaces in the friction track were observed in comparison to poly-α-olefin. Fourier-Transform infrared spectroscopy analysis suggested that the ether groups were attracted to the worn steel surface, phenyl groups became consequently perpendicular, and the attached alkyl chains repelled other substances and prevented further wear of the surface. Moreover, ADEs showed a high adaptability with traditional additives.

21 October 2022 in Lubricants
Verified
Journal Article
Open access
PDF file
Renguo LURenguo LU
Renguo LU
HTHiroshi Tani
Hiroshi Tani
SKShinji Koganezawa
Shinji Koganezawa
MHMasayuki Hata
Masayuki Hata
Lubricants exhibiting both thermal and chemical stability that consequently generate less hydrogen during friction are required to avoid the hydrogen embrittlement of moving mechanical components. The present work studied the effects of the length and number of alkyl chains on the tribological properties of polyphenyl ethers (PPEs), which feature good thermal and radiation resistance. PPEs were found to have much lower friction coefficients compared with a poly-alpha-olefin and alkyldiphenyl ether, and the effect of the running-in process on friction appeared to be negligible. The formation of polymers on the friction track evidently decreased the friction coefficients of the lubricants and the wear rates were almost zero for all the PPEs, indicating excellent anti-wear properties. Analyses with a quadrupole mass spectrometer connected to a friction tester under vacuum indicated negligible hydrogen generation from 4P2E, which had no alkyl chains, after the running-in. R1-4P2E, having a C16H33 chain, showed hydrogen desorption similar to that of the alkyldiphenyl ether, which had a C18H37 alkyl chain. R2-4P2E, with two C16H33 chains, produced significant hydrogen, but with a long induction period; thus, it provided good wear protection. Although alkyl chains increased the risk of hydrogen generation, PPEs with such chains may have applications as standard lubricants.