Monica Katherine Gonzalez

Monica Katherine Gonzalez

Auto-generated profile, based on publicly available information

Monica Katherine Gonzalez

Department of Production Engineering, KTH Royal Institute of Technology, Stockholm, Sweden

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 June 2023 in Journal of Intelligent Manufacturing
Verified
Journal Article
Open access
PDF file
Eleonora IunusovaEleonora Iunusova
Eleonora Iunusova
MGMonica Katherine Gonzalez
Monica Katherine Gonzalez
KSKároly Szipka
Károly Szipka
AAAndreas Archenti
Andreas Archenti
The early identification of a defect that is developing in a bearing is crucial for avoiding failures in rotating machinery. Frequency domain analysis of the vibration signals has been shown to contribute to a better understanding of the nature of a developing defect. Early signs of degradation might be more noticeable in certain frequency bands. The advantages in identifying and monitoring these bandwidths are several: prevention of serious machinery damages, reduction of the loss of investments, and improvement of the accuracy in failure predicting models. This paper presents and compares two approaches for the diagnosis of bearing faults. The first approach was knowledge-based. It relied on principles of mechanics to interpret the measured vibration signals and utilized prior knowledge of the bearing characteristics and testing parameters. The second approach was data-driven whereby data were acquired exclusively from the vibration signal. Both approaches were successfully applied for fault diagnosis by identifying the frequencies of the vibration spectra characteristic for the bearing under study. From this, bandwidths of interest for early fault detection could be determined. The diagnostic abilities of both approaches were studied to analyze and compare their individual strengths regarding the aspects of implementation time, domain knowledge, data processing associated knowledge, data requirements, diagnostic performance, and practical applicability. The advantages, apparent limitations as well as avenues for further improvement of both approaches are discussed.

22 January 2022 in Robotics and Computer-Integrated Manufacturing
Verified
Journal Article
Open access
MGMonica Katherine Gonzalez
Monica Katherine Gonzalez
NTNikolas Alexander Theissen
Nikolas Alexander Theissen
ABAsier Barrios
Asier Barrios
AAAndreas Archenti
Andreas Archenti

4 February 2025 in Journal of Manufacturing Systems
Verified
Journal Article
Open access
MGMonica Katherine Gonzalez
Monica Katherine Gonzalez
MCMariano Jose Coll-Araoz
Mariano Jose Coll-Araoz
AAAndreas Archenti
Andreas Archenti

7 January 2023 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
MGMonica Katherine Gonzalez
Monica Katherine Gonzalez
NTNikolas Theissen
Nikolas Theissen
NANora Agirre
Nora Agirre
JLJon Larrañaga
Jon Larrañaga
PHPatxi Hacala
Patxi Hacala
AAAndreas Archenti
Andreas Archenti
This article presents the measurement and analysis of the influence of velocity on the quasi-static deflections of industrial manipulators of three different manufacturers. Quasi-static deflection refers to the deflection of the end effector position of articulated robots during movement at low velocity along a predefined trajectory. Based on earlier reported observations by the authors, there exists a difference in the static and quasi-static deflections considering the same points along a trajectory. This work investigates this difference to assess the applicability of robotic compliance calibration at low velocities. For this assessment, the deflections of three industrial articulated robots were measured at different speeds and loads. Considering the similarity among the robot models used in this investigation, this work also elaborates on the potential influence of the measurement procedure on the measured deflections and its implications for the compliance calibration of articulated robots. For all industrial articulated robots in this investigation, the quasi-static deflections are significantly larger than the static ones but similar in trend. Additionally, the magnitude of the quasi-static deflections presents a proportional relationship to the Cartesian velocity.

15 April 2025 in CIRP Annals
Verified
Journal Article
Closed access
MGMonica Katherine Gonzalez
Monica Katherine Gonzalez
TLTheodoros Laspas
Theodoros Laspas
HLHung-Ching Lin
Hung-Ching Lin
KHKanako Harada
Kanako Harada
AAAndreas Archenti
Andreas Archenti

4 November 2025 in IEEE Access
Verified
Journal Article
Open access
MKMárton Kovács
Márton Kovács
MGMonica K. Gonzalez
Monica K. Gonzalez
AAAndreas Archenti
Andreas Archenti
As prediction models for automated decision-making in manufacturing become more widespread, enhancing their reliability has become increasingly critical. One effective approach is improving the quality of training data through data curation or cleaning. However, most existing data curation methods rely on domain-specific expertise in data science, limiting their accessibility. To address this challenge, a general-purpose time-series data curation toolbox with a user-friendly interface was developed. Designed to minimize user input while maintaining traceability, the toolbox was tested on various publicly available time-series datasets. Its performance was evaluated by comparing the prediction accuracy of machine learning models trained on original versus cleaned data. The results demonstrate the significant potential of the general-purpose toolbox for enhancing data quality and model performance across a range of applications.