Purpose: The purpose of Part I of this paper is to investigate the influence of Bi additions on the surface tension, the interfacial tension, and the density of SnZn7Bi alloys (Bi=1 and 3 percent by mass) as a continuation of similar previous studies on Bi and Sb additions to the binary Sn‐Zn alloy. The main aim of Part I is to indicate that the lowering of the surface tension and interfacial tension is not sufficient for practical applications. However, knowledge of the interfacial tension between the soldering flux and the solder is necessary to convert the wetting force into the contact angle. This will be documented in Part II.Design/methodology/approach: The maximum bubble method was applied for the surface tension and the Miyazaki method was applied for the surface tension and the interfacial tension, using the density values from the dilatometric technique. The experimental surface tension results are compared with the Butler's thermodynamic modeling results and are discussed by means of the analysis of variance (ANOVA).Findings: On the basis of previous studies on Sn‐Zn‐Bi‐Sb alloys, the addition of Bi to SnZn7 slightly decreased the surface tension measured in an Ar+H2atmosphere, similarly to the Butler's modeling results. Also, a similar slight decrease of the surface tension from the Miyazaki method measured in air and in nitrogen was observed, as well as a more significant lowering of the interfacial tension with the use of a flux in nitrogen. There was also a slight influence of the temperature on the numerical values of the surface tensions and the interfacial tension. In the ANOVA, taking into account the Bi content, the temperature of measurements, the atmosphere and the flux, the flux used was shown as the most important, and also, to a lesser extent, the atmosphere.Research limitations/implications: It is intended (the purpose of Part II of this paper) to verify the positive influence of Bi additions in SnZn7 alloys on the surface tensions and the interfacial tensions via the contact angles from the interaction with Cu on printed circuit board with different lead‐free finishes.Practical implications: It is suggested that further studies on more efficient fluxes are necessary for the practical application being in agreement with the ANOVA and the literature information.Originality/value: A slight improvement of the wettability with the use of Bi additions in the SnZn7Bi alloys in the course of various experimental techniques is proven, similar to results reported in various references. The obtained results will enlarge the SURDAT database of lead‐free soldering materials.
17 April 2023 in Journal of Materials Engineering and Performance
This paper presents the results of the Ni substrate wetted with the liquid Sn-Zn eutectic alloy with the addition of Ag, Al, and Li (84.3 at.% Sn, 13.7 at.% Zn, 1 at.% Ag, 0.5 at.% Al, and 0.5 at.% Li-SZAAL). The wetting tests were performed using two methods: the wetting balance tests (WBT) and the sessile drop (SD) method at 250 °C, in the presence of an ALU33® flux. The wetting times were 5, 20, 60, 180, and 1800 s. Next, the microstructure of selected solidified solder joints was investigated using scanning electron microscope. The Ni-Zn system's intermetallic phases (IMCs) were identified at the solder–Ni substrate interface. The kinetics of the formation and growth of the IMC layer was determined. Interfacial tension and contact angle (CA) values were calculated from WBT measurements in the presence of the ALU33® flux. Interfacial tension was compared to surface tension from the maximum bubble pressure and CA values to those obtained using the SD method. The value of the contact angle of SZAAL on Cu (39°) substrate is lower than on Ni (43°). For the comparison, also the interaction between SZAAL and Cu substrate was measured. After 1800 s, the IMCs thickness is significantly reduced for Ni pad than for Cu substrate. The study found that the addition of Al, Ag, and Li improved the tensile strength and wettability of Sn-Zn eutectic-based alloys.