Carlos Henrique da Silva

Carlos Henrique da Silva

Auto-generated profile, based on publicly available information

Carlos Henrique da Silva

Universidade Tecnológica Federal do Paraná, Brasil

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2012 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Open access
PDF file
MMMarco Antonio Muraro
Marco Antonio Muraro
FKFábio Koda
Fábio Koda
UJUrbano Reisdorfer Jr.
Urbano Reisdorfer Jr.
CSCarlos Henrique da Silva
Carlos Henrique da Silva
One of the main gear damage mechanisms is the formation of pitting and spalling on the tooth flank. Several factors have significant influence on the damage formation, such as: contact stress level; tooth profile type; relative contact speed; surface finish and lubrication conditions. This work comprehends the global observation of all such parameters and was carried out to explain the phenomena related to this wear mechanism. The wear test equipment uses the power recirculation principle and is commonly known as FZG test rig. The gears were made from AISI 8620 steel and had two types of surface finishing (by shaving or by milling). The wear experiments were performed with two torque stages: 135 N.m (running-in) and 302 N.m (steady-state), and two test temperatures: 60ºC (running-in) and 90ºC (steady-state). The wear level was determined by using image analysis. In order to calculate the specific film thickness and friction coefficient, the roughness of tooth flank was measured at each test stop. After the experiments were completed, it was possible to confirm that, for both manufacturing processes, the boundary lubrication regime was adopted at the tooth flank and the specific film thickness presents a different behavior when compared to addendum, pitch diameter and deddendum regions. The wear on the gear flanks depended on the lubricant film thickness and it was higher for the milled gears

1 January 2022 in Materials Research
Verified
Journal Article
Open access
Rafael Luciano DalcinRafael Luciano Dalcin
Rafael Luciano Dalcin
ARAlexandre da Silva Rocha
Alexandre da Silva Rocha
VCVictor Velho de Castro
Victor Velho de Castro
JNJulio Cesar Klein das Neves
Julio Cesar Klein das Neves
CSCarlos Henrique da Silva
Carlos Henrique da Silva
CMCélia de Fraga Malfatti
Célia de Fraga Malfatti

1 January 2021 in Materials Research
Verified
Journal Article
Open access
Rafael Luciano DalcinRafael Luciano Dalcin
Rafael Luciano Dalcin
ARAlexandre da Silva Rocha
Alexandre da Silva Rocha
VCVictor Velho de Castro
Victor Velho de Castro
LOLeonardo Fonseca Oliveira
Leonardo Fonseca Oliveira
JNJulio Cesar Klein das Neves
Julio Cesar Klein das Neves
CMCélia de Fraga Malfatti
Célia de Fraga Malfatti

21 November 2023 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
Rafael Luciano DalcinRafael Luciano Dalcin
Rafael Luciano Dalcin
VMValcir Marques de Menezes
Valcir Marques de Menezes
ARAlexandre da Silva Rocha
Alexandre da Silva Rocha
SMSamara Paulin de Moraes
Samara Paulin de Moraes
LALeonardo Bottega Affonso
Leonardo Bottega Affonso
CSCarlos Henrique da Silva
Carlos Henrique da Silva

1 September 2022 in Surface Topography: Metrology and Properties
Verified
Journal Article
Closed access
Oriana Palma CalabokisOriana Palma Calabokis
Oriana Palma Calabokis
Yamid E. Nuñez de la RosaYamid E. Nuñez de la Rosa
Yamid E. Nuñez de la Rosa
SMSamara Paulin de Moraes
Samara Paulin de Moraes
EAEstela Vicentim Antunes
Estela Vicentim Antunes
TCTiago Cousseau
Tiago Cousseau
CSCarlos Henrique da Silva
Carlos Henrique da Silva
Gear manufacturers must make decisions about the manufacturing materials and superficial treatments. The best performance as to a type of failure should be evaluated. However, it is a time-demanding and costly process. The present work proposes a methodology for a comprehensive assessment (experimental and computational) of contact fatigue of gears in FZG test rig. The materials investigated were 18CrNiMo7-6 and 20MnCr5 alloy steels, widely used in industrial and automotive transmission systems, but with very different raw material costs, which can exceed twice the first compared to the second. The study evaluated the contact analysis between gears from the macroscopic point of view and the microscopic (inclusion of roughness). At the same time, the evolution of roughness and pit-damaged area after each test stage was monitored. The approach determined the stress field after each loading cycle and thus correlating the regions of higher stresses with surface and subsurface fatigue (micropitting and pitting). In addition, Weibull’s statistical analysis and SEM-EDS observations were executed. In many cases, the methodology correlated the increased roughness and pitting affected area with the regions submitted to the higher contact stress. Observations by SEM-EDS revealed that the occurrence of plastic deformation as a mechanism of wear should be considered in the equations of microscopic stress analysis. The similar fatigue life of such different materials may be correlated to the competitive mechanisms of higher mechanical strength of 18CrNiMo7-6 and better crack propagation characteristics of 20MnCr5. The methodology proved to be consistent for fatigue failure analysis of gears in FZG test rig.

14 March 2025 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Closed access
LMLucas Gimenis de Moura
Lucas Gimenis de Moura
CSCarlos Henrique da Silva
Carlos Henrique da Silva
RTRafael Mello Trommer
Rafael Mello Trommer
CAClara Muniz Almeida
Clara Muniz Almeida
MMMarcia Marie Maru
Marcia Marie Maru
CRCarlos Rodrigo de Mello Roesler
Carlos Rodrigo de Mello Roesler