30 October 2025 in IEEE Journal of Solid-State Circuits
This article presents a fully integrated 77-GHz hybrid time-division-multiplexing multiple-input–multiple-output (TDM-MIMO) phased-array radar in a 55-nm CMOS process. The system integrates eight independent transmitters ( $8~{\times }~1$ TXs) and two four-channel phased-array receivers ( $2~{\times }~4$ RXs), achieving a $4.76{\times }$ increase in detection range compared to single-input–single-output (SISO) architecture in long-range radar (LRR) mode and 1.79° angular resolution with $16 {\times } 4$ virtual array in short-range radar (SRR) mode. To realize a large chirp bandwidth while maintaining low voltage-controlled oscillator (VCO) gain ( $K_{\text {VCO}}$ ), a zig-zag phase-locked loop (PLL)-based frequency-modulated continuous wave (FMCW) generator is proposed, enabling continuous multi-subband chirping. By monitoring the voltage across the capacitance in loop filter ( $V_{\text {CAP}}$ ) for subband switching, the tuning voltage ( $V_{\text {TUNE}}$ ) is configured to the optimal switching voltage, eliminating the frequency ripple ( $F_{R}$ ) during subband switching. Each TX channel integrates switches to support a flexible number and positioning of 1–8 transmitters in TDM mode. To mitigate the leakage effect caused by variations in amplitude and phase due to the varying number and position of TX on-channels, a receiver architecture with three low noise amplifiers (LNAs) and a 4-bit phase shifter is designed to achieve low noise figure (NF) and high linearity. Furthermore, an I/Q mixer is designed to achieve orthogonal-ellipse-overlapping-shape NF and petal-shape linearity over a phase difference range of 0°– ${360^{\circ } }~{\Delta \phi _{\text {leak}}}$ between the local oscillator (LO) and leakage. The chip achieves a measured maximum chirp bandwidth of 12.6-GHz spanning four zig-zag subbands. The root-mean-square (rms) frequency error is 0.0068% at 18.8-MHz/ $\mu $ s chirp rate with 2.5-GHz bandwidth, and 0.3% at 545-MHz/ $\mu $ s chirp rate with 2.65-GHz bandwidth. The eight-channel TX achieves a maximum effective isotropic radiated power (EIRP) of 32 dBm at 78.8 GHz, while the four-channel RX achieves a minimum NF of 16.3 dB at a 2-MHz intermediate frequency (IF). The hybrid radar achieves a detection range of 186 m and a range resolution of 3 cm.
18 February 2026 in IEEE Transactions on Microwave Theory and Techniques
This article presents a Doppler-assisted frequency-modulated continuous-wave (FMCW) radar that combines precise range resolution capability of FMCW with high sensitivity of Doppler radar, enabling versatile performance for indoor applications. A comprehensive analysis of low-frequency noise contributions from key receiver (RX) blocks including low-noise amplifier (LNA), mixer, local oscillator (LO) buffer, and analog baseband (ABB) circuits is conducted. An “RF+LO+BB” joint noise figure (NF) improvement method is proposed to effectively suppress the low-frequency noise. To minimize frequency modulation (FM) error in charge-pump-based fractional-N phase-locked loops (PLLs), a nested-PLL architecture with an optimized loop parameter selection method is employed, significantly enhancing chirp linearity. Fabricated in a 55-nm CMOS technology, the proposed Doppler-assisted FMCW radar achieves NFs of 32.13 and 12.94 dB at 10 Hz and 1 kHz, respectively, and a chirp linearity of 0.0039% over a 3.52 GHz chirp bandwidth (BW), resulting in a maximum detection range of 19.41 m and a range resolution of 4.7 cm. The radar occupies a die area of 12.7 mm2 and consumes 594 mW in FMCW mode and 432 mW in Doppler mode under a 3.3 V supply.