8 February 2019 in Chempluschem
27 October 2017 in ACS Omega
Around 10% of the worldwide annual production of gold is used for manufacturing of electronic devices. According to the European Commission, waste electric and electronic equipment is the fastest growing waste stream in the European Union. This has generated the need for an effective method to recover gold from electronic waste. Here, we report a simple, effective, and highly selective nylon-12-based three-dimensional (3D)-printed scavenger objects for gold recovery directly from an aqua regia extract of a printed circuit board waste. Using the easy to handle and reusable 3D-printed meshes or columns, gold can be selectively captured both in a batch and continuous flow processes by dipping the scavenger into the solution or passing the gold-containing solution through the column. The possibility to optimize the shape, size, and flow properties of scavenger objects with 3D printing enables the gold scavengers to match the requirements of any processing plants.
24 July 2018 in Advanced Sustainable Systems
11 July 2019 in ACS Omega
Three-dimensional selective laser sintering printing was utilized to produce porous, solid objects, in which the catalytically active component, Pd/SiO2, is attached to an easily printable supporting polypropylene framework. Physical properties of the printed objects, such as porosity, were controlled by varying the printing parameters. Structural characterization of the objects was performed by helium ion microscopy, scanning electron microscopy, and X-ray tomography, and the catalytic performance of the objects was tested in the hydrogenation of styrene, cyclohexene, and phenylacetylene. The results show that the selective laser sintering process provides an alternative and effective way to produce highly active and easily reusable heterogeneous catalysts without significantly reducing the catalytic efficiency of the active Pd/SiO2 component. The ability to control the size, porosity, mechanical properties, flow properties, physical properties, and chemical properties of the catalyst objects opens up possibilities to optimize devices for different reaction environments including batch reactions and continuous flow systems.
1 October 2019 in ACS Omega
Three-dimensionally printed solid but highly porous polyamide-12 (PA12) plate-like filters were used as selective adsorbents for capturing tetrachloroaurate from acidic solutions and leachates to prepare PA12–Au composite catalysts. The polyamide-adsorbed tetrachloroaurate can be readily reduced to gold nanoparticles by using sodium borohydride, ascorbic acid, hydrogen peroxide, UV light, or by heating. All reduction methods led to polyamide-anchored nanoparticles with an even size distribution and high dispersion. The particle sizes were somewhat dependent on the reduction method, but the average diameters were typically about 20 nm. Particle sizes were determined by using a combination of single-particle inductively coupled plasma mass spectrometry, helium ion microscopy, and powder X-ray diffraction. Dispersion of the particles was analyzed by scanning electron microscopy with energy-dispersive spectroscopy. Due to the high adsorption selectivity of polyamide-12 toward tetrachloroaurate, the three-dimensional-printed filters were first used as selective gold scavengers for the acidic leachate of electronicwaste (WEEE). The supported nanoparticles were then generated directly on the filter via a simple reduction step. These objects were used as catalysts for the reduction of 4-nitrophenol to 4-aminophenol. The described method provides a direct route from waste to catalysts. The selective laser sintering method can be used to customize the flow properties of the catalytically active filter object, which allows the optimization of the porous catalytic object to meet the requirements of catalytic processes.
10 January 2019 in ACS Applied Energy Materials
Selective Laser Sintering (SLS) 3D printing was utilized to fabricate highly porous carbon electrodes. The electrodes were prepared by using mixture of fine graphite powder and either polyamide-12, polystyrene or polyurethane polymer powder as SLS printing material. During the printing process graphite powder was dispersed uniformly on the supporting polymer matrix. Concentration of graphite in the mixture was varied between 5 and 40 wt-% to find the correlation between the carbon content and conductivity. The graphite concentration, polymer matrix and the printing conditions all have an impact on the final conductivity. Due to the used SLS printing technique, all printed electrodes were highly porous. By using polyurethane as the supporting matrix, it was possible to produce flexible electrodes in which the conductivity is sensitive to pressure and mechanical stress. Physical properties such as graphite distribution, attachment and the overall porosity of the printed electrodes were studied using scanning electron microscopy (SEM), helium ion microscopy (HIM) and X-ray tomography. The results show that combination of chemical design of the printing material and use of SLS 3D printing technique enables fabrication of highly customizable electrodes with desired chemical, physical, mechanical, and flow-through properties.