8 April 2013 in SAE International Journal of Fuels and Lubricants
This paper examines the effect of charge cooling on the Research Octane Number (RON) of ethanol/gasoline blends. While gasoline is fully vaporized prior to entry into the engine in a standard RON test, significant charge cooling is observed for blends with high ethanol content, with the presence of a near-saturated and potentially two-phase air-fuel mixture during induction. Thus, the relative significance of the charge cooling and the autoignition chemistry cannot be determined from the standard RON test.In order to better delineate the effects of charge cooling and autoignition chemistry, a so-called ‘modified RON’ test is therefore devised in which the temperature of the air-fuel mixture entering the engine is fixed and representative of that observed for primary reference fuels (PRFs). Thermodynamic modeling of this modified RON test suggests the mixture is always fully vaporized prior to compression, and that the modified RON test maintains much more constant temperatures during compression, regardless of the enthalpy of vaporization. The modified RON test thus appears to be a more practical means of examining the significance of autoignition chemistry of various fuels, particularly gasoline blends with significant alcohol content.
28 March 2017 in SAE International Journal of Engines
Most studies on knock ignore the stochastic nature of knock and focus on the onset of knock which is determined by chemical kinetics. This paper focuses on knock intensity (KI) which is determined by the evolution of the pressure wave following knock onset in a hot spot and highlights the stochastic processes involved.KI is defined in this study as the maximum peak-to-peak pressure fluctuation that follows the onset of knock. It depends on ξ = (a/ua) where ua is the speed of the autoignition front and a is the speed of sound. When ua is small, KI can be related to the product of a parameter Z, which depends on Pko, the pressure at knock onset and the square of (∂x/∂T), which is the inverse of the gradient of temperature with distance in the hot spot. Both Z and (∂x/∂T) were calculated using measured KI and Pko for hundreds of individual knocking cycles for different fuels. The model for ignition delay as a function of pressure P and T in the hot spot and other data needed to calculate Z were available from a previous study (SAE 2016-01-0702). For a given fuel and operating condition, Z varies because Pko varies, because of cyclic variation of combustion - a stochastic process. (∂x/∂T) depends on the evolution of the hot spot during the engine cycle and depends on flow and turbulence - another stochastic process. All else being equal, Z increases and hence the probability of high KI increases as Pko increases, e.g., by more advanced spark timing and/or faster flame development. For a given Pko, Z is lower for a fuel with higher RON. In modern turbocharged engines extremely high intensity knock, informally termed superknock is observed to occur occasionally even though operating conditions are chosen to avoid knock. Superknock is caused by developing detonation (DD) which results when the value of ξ decreases and the pressure wave begins to couple with the autoignition front and gets amplified. Autoignition has to be initiated at high P and T for superknock to occur. At practical operating conditions, this can only happen via another abnormal stochastic phenomenon - preignition, when a flame is established before the spark plug fires. Both preignition and superknock become more likely as P increases. All else being equal, the probability of superknock decreases as the fuel RON is increased. However, even with high RON, high KI and superknock could occur with the right combination of P and (∂x/∂T).
17 October 2016 in SAE International Journal of Fuels and Lubricants
The effect of ethanol blended with three FACE (Fuels for Advanced Combustion Engines) gasolines, I, J and A corresponding to RON 70.3, 71.8 and 83.5, respectively, were compared to PRF70 and PRF84 with the same ethanol concentrations, these being 2%, 5%, 10%, 15% and 20% by volume. A Cooperative Fuel Research (CFR) engine was used to understand the blending effect of ethanol with FACE gasolines and PRFs in spark-ignited and homogeneous charge compression ignited mode. Blending octane numbers (BON) were obtained for both the modes. All the fuels were also tested in an ignition quality tester to obtain Blending Derived Cetane numbers (BDCN). It is shown that fuel composition and octane number are important characteristics of all the base fuels that have a significant impact on octane increase with ethanol. The dependency of octane number for the base fuel on the blending octane number depended on the combustion mode operated. The aromatic composition in the base fuel, effects blending octane number of the mixture, for fuels with higher aromatic content lower blending octane numbers were observed for ethanol concentration.