1 February 2018 in IEEE Journal of Solid-State Circuits
This paper presents a ``fully-connected'' hybrid beamforming receiver that independently weights each element in an antenna array prior to separate downconversion chains that output independent baseband streams. A receiver architecture is introduced, which implements RF-domain complex-valued Cartesian weighting, RF-domain combining, and multi-stream heterodyne complex-quadrature downconversion. Each RF-domain Cartesian weight is implemented by a pair of 5-bit digitally controlled programmable-gain amplifiers, whose outputs are combined with the weighted signals from other antennas prior to complex-quadrature downconversion. Signal combination is performed by a wideband small-footprint distributed active combiner. A 25-30 GHz hybrid beamforming receiver with eight antenna inputs and two baseband output streams is designed in 65-nm CMOS. In each antenna path, the receiver achieves 34-dB conversion gain, 7.3-dB minimum noise figure, and 5 GHz of RF bandwidth. The entire receiver consumes 340 mW (equivalent to 27.5 mW per antenna per stream) including low-noise amplification, RF-domain beamforming, multi-stream downconversion, and local oscillator generation and distribution circuitry. The receiver occupies 3.86 mm² excluding pads, equivalent to 0.36 mm² per antenna per stream. Single-element characterization results are presented, along with characterization of several spatial processing techniques including interference cancellation (20 dB peak to null for two elements), simultaneous two-stream reception, and adaptive-codebook-search-based beam acquisition.
24 January 2019 in IEEE Journal of Solid-State Circuits
This paper presents a multi-standard fully connected hybrid beamforming (FC-HBF) receiver that can be reconfigured between two fully connected two-stream multi-input-multi-output (MIMO) modes at 28- or 37-GHz band, and an inter-band carrier-aggregation (CA) mode enabling concurrent single-stream operation at 28 and 37 GHz. A new image-reject (IR) heterodyne beamforming architecture is introduced that facilitates easy reconfiguration. Concurrent dual-band operation of the beamformer front end is achieved by using an inherently wideband Cartesian-combining-based RF-domain complex-weighting architecture, which is implemented using coupled-resonator-based dual-band gain stages, and current-mode dual-band active combiners. The downconversion stage comprises a cascade of complex-quadrature mixing stages that combines Cartesian complex-weighting operation with image rejection. A new quadrature error detection and calibration scheme is also introduced to improve the image rejection of the proposed architecture. A minimum mean-square error (MMSE) beam adaptation technique, introduced for the first time in an RF or hybrid beamformer, breaks the need for individual access to the beamformer inputs needed in a traditional least-mean-square (LMS) scheme and allows both main lobe and null adaptation. A 28-/37-GHz hybrid beamforming receiver with four antenna inputs and two baseband output streams is designed in 65-nm CMOS that demonstrates the above features. In each antenna path, the receiver achieves 33-dB (26.5 dB) peak conversion gain, 2.75-GHz (3.75 GHz) RF bandwidth, and 5.7-dB (8.5 dB) NF at 28 GHz (37 GHz). The entire receiver consumes 310 mW and occupies 2.2 mm 2 core area. Extensive characterization results for single-element and several multi-element scenarios are presented including concurrent dual-band receiving (>35-dB image rejection), null-steering (>25-dB peak to null for two elements), and multi-element CA (~50-dB inter-carrier interference rejection).
29 September 2021 in IEEE Journal of Solid-State Circuits
This article presents a two-layer low-complexity fully connected (FC) RF/analog weighting multi-input–multi-output (MIMO) transceiver comprising an RF weight layer and an analog–baseband weight layer. The transceiver can serve as a small-scale MIMO system by itself and can serve as the building block in a larger hybrid MIMO system. The architecture mitigates the complexity versus spectral-efficiency tradeoffs of existing MIMO architectures and enables MIMO stream/user scalability, superior energy efficiency, and spatial-processing flexibility. A compact, reconfigurable bidirectional circuit architecture is introduced, including a new Cartesian-combining/splitting beamforming receiver/transmitter, dual-band bidirectional beamforming network, dual-band frequency translation chains, and baseband Cartesian beamforming with an improved programmable gain amplifier design. A 28-/37-GHz band, two-layer, eight-element, four-stream hybrid MIMO transceiver prototype is designed in 65-nm CMOS to demonstrate the above features. The prototype achieves accurate beam/null-steering capability, excellent area/power efficiency, and state-of-the-art TX/RX mode performance in two simultaneous bands while demonstrating multi-antenna (up to eight) multi-stream (up to four) over-the-air spatial multiplexing operation using the proposed energy-efficient two-layer hybrid beamforming scheme.
8 May 2020 in IEEE Journal of Solid-State Circuits
This article describes system and circuit design techniques to enhance power efficiency and incorporate new features in millimeter-wave multi-input-multi-output (MIMO) transceivers. The higher peak-to-average power ratio (PAPR) of the signal transmitted from a digital beamformer (DBF) or a fully connected hybrid beamforming (FC-HBF) transmitter compared with the conventional partially connected hybrid beamforming (PC-HBF) transmitter is identified for the first time. It is then shown that when a power amplifier (PA) with better back-off efficiency than Class-A PA is used, the overall power efficiency of the FC-HBF is superior to the PC-HBF for a given antenna geometry. Second, a new mechanism for built-in dual-band, per-element self-interference cancellation (SIC) is introduced to enable multi-antenna frequency-division-duplex (FDD) and full-duplex (FD) operation. Such SIC can only be supported in the proposed FC-HBF architecture. Several innovative circuit concepts are introduced, including low-loss wideband antenna interface design, dual-band power combining PA, dual-band RF-SIC design, and bidirectional MIMO signal path design. To demonstrate these techniques, a 28-/37-/39-GHz bidirectional two-stream front-end single-element prototype is designed in the 65-nm CMOS. The prototype can be configured as a transmit (TX) or receive (RX) element in DBFs or FC-HBFs which can in turn be configured to support TDD, FDD, or FD operation. The front-end achieves 16-/11-dB RX gain, 6.2-/7-dB NF, 15.8-/16.8-dBm saturated PA output power, and 20%/21.6% peak PA efficiency in the 28-/37-GHz bands. Extensive characterization results are presented to compare the energy efficiencies of the PC-HBF and FC-HBF architectures. The prototype is also characterized in the FDD/FD mode and achieves 36-dB peak RF-domain SIC and better than 26-dB RF-domain SIC across 0.5-GHz modulation bandwidth.
23 April 2018 in IEEE Journal of Solid-State Circuits
VSV. Srinivasa Somayazulu
+3
This paper presents an 802.11g/n compliant wake-up radio solution that consists of an innovative on–off keying (OOK) emulating orthogonal frequency division multiplexing (OFDM) modulation scheme, and a fully integrated, highly scaled, ultra-low power wake-up receiver design in 14-nm FinFET CMOS technology requiring only a 32-kHz real-time clock reference. The receiver achieves −72-dBm sensitivity and +20 dBr adjacent channel interference (ACI) rejection at 10−3 bit error rate (BER) while consuming $95~\mu \text{W}$ . This receiver can be utilized along with any legacy Wi-Fi transmitter without changing any hardware.
22 April 2020 in IEEE Transactions on Microwave Theory and Techniques
This article presents design techniques to facilitate the use of the driving point impedance (Z₁₁) of one-port transformer-coupled resonators as wideband loads of millimeter-wave amplifier stages for a 28-GHz receiver front end. While the use of both the Z₁₁ of a one-port and the transimpedance (Z₂₁) of a two-port coupled resonator is considered to achieve a wideband response, it is shown that under conditions of low magnetic coupling and constrained network quality factor, the use of Z₁₁ can result in a higher gain-bandwidth product of low-noise amplifier (LNA) amplifier stages. The effect of the complex zero in the Z₁₁ response on the in-band gain ripple is shown to be alleviated merely by lowering the quality factor of the transformer's secondary coil; this strongly motivates the use of compact, nested-inductor transformer layouts. Implemented in a 65-nm CMOS process, a three-stage LNA (with Z₁₁ wideband loads in two stages) achieves a 24.4-32.3-GHz bandwidth (27.9 % fractional bandwidth), a peak S₂₁ of 24.4 dB (20.4 dB), a minimum noise figure (NF) of 4 dB (4.6 dB), and an input-referred P1dB of -23 dBm (-22 dBm) while consuming 22-mW (9.9 mW) power from a 1.1-V (0.85 V) supply. The use of compact transformers limits the LNA's footprint to only 0.12 mm². A 26.5-32.5-GHz quadrature receiver prototype employing the LNA achieves a 29.5-dB peak conversion gain, a 5.3-dB minimum NF, and a -26-dBm input-referred P1dB while consuming 33 mW from a 1.1-V supply.