Magnetically hard and nanoparticles have been produced by using surfactant-assisted low- and high-energy ball milling techniques. Surfactants prevent the rewelding of the crashed particles during the milling process. Heptane was used as the milling medium and oleic acid as the surfactant. High-energy ball milling experiments took place in a milling vial with carbon steel balls by using an SPEX 8000M high-energy ball milling machine. The coercivity was found to increase with milling time with values of 2.3 kOe for and 18.6 kOe for after 4 h of milling. Transmission electron microscopy data showed that the milled powders consisted of nanoparticles with an average size of 5–6 nm and a narrow size distribution. Samples deposited on copper coated carbon grid showed self-assembled nanoparticles which could be further aligned when subjected to a magnetic field.
30 March 2010 in Journal of Physics: Condensed Matter
High-energy ball milling has been shown to be a promising method for large-scale fabrication of rare earth-transition metal nanoparticles. In this work, we report crystallographically anisotropic SmCo(5), PrCo(5) and Sm(2)(Co, Fe)(17) nanoparticles (particle size smaller than 10 nm) obtained by surfactant-assisted ball milling and study their size and properties as a function of the milling conditions. By milling nanocrystalline precursor alloys, we obtained SmCo(5) platelets (flakes) approximately 100 nm thick with an aspect ratio as high as 10(2)-10(3). The unusual shape evolution of this brittle material is attributed to its increased plasticity in the nanocrystalline state. The nanoflakes are susceptible to re-crystallization annealing and exhibit a room-temperature coercivity of up to 19 kOe. The successful fabrication of rare earth-cobalt nanoparticles and ultra-thin flakes provides hope for the development of nanocomposite permanent magnets with an enhanced energy product.
High energy ball milling has been shown to be a promising method for large-scale fabrication of rare earth-transition metal nanoparticles. In this work, magnetically hard Nd-Fe-B nanopowders with a coercivity in the range of 1.2-4 kOe have been produced by surfactant-assisted ball milling of nanocrystalline precursor alloys. The nanopowders consisted of Nd(2)Fe(14)B flakes with a thickness below 100 nm and an aspect ratio as high as 10(2)-10(3) and anisotropic square nanoparticles with a size of 11 nm. Both the nanoparticles and nanoflakes showed a strong [001] out-of-plane texture. The nanoparticles showed a spin reorientation temperature which is lower (117 K) than the bulk value (135 K). The successful fabrication of Nd-Fe-B nano-thin flakes and anisotropic nanoparticles provides hope for the development of nanocomposite permanent magnets with an enhanced energy product.
Anisotropic Nd2Fe14B nanoparticles and nanoflakes have been produced by surfactant-assisted high-energy ball milling (SA-HEBM) of precursor nanocrystalline alloys. A two-stage high-energy ball milling was performed to obtain the nanopowders and nanoparticles; first the coarse powders were subjected to a wet milling followed by a wet surfactant-assisted milling. Different shaped nanoparticles have been obtained by varying the time of the first stage of the milling process and then separated by sonication. For a surfactant-free wet milling of 4 h, followed by the SA-HEBM, the nanopowders consisted of a mixture of Nd2Fe14B flakes with a thickness below 200 nm and an aspect ratio as high as 102–103, and anisotropic square nanoparticles with a size of 10 nm. However, for a shorter wet milling, nearly spherical nanoparticles with a size of 2.7 nm were obtained. Low-temperature coercivities have been obtained with maximum values of 4 kOe for square nanoparticles and 2.5 kOe for the nearly spherical nanoparticles.
4 February 2020 in Journal of Applied Polymer Science