Zhen Shang

Zhen Shang

Auto-generated profile, based on publicly available information

Zhen Shang

Jilin University

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2019 in Fuel
Verified
Journal Article
Closed access
ZSZhen Shang
Zhen Shang
XYXiumin Yu
Xiumin Yu
WSWeibo Shi
Weibo Shi
SHShan Huang
Shan Huang
GLGuanting Li
Guanting Li
FHFengshuo He
Fengshuo He

1 June 2020 in Fuel
Verified
Journal Article
Closed access
GLGuanting Li
Guanting Li
XYXiumin Yu
Xiumin Yu
ZJZhaohui Jin
Zhaohui Jin
ZSZhen Shang
Zhen Shang
DLDecheng Li
Decheng Li
ZZZhe Zhao
Zhe Zhao

23 May 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
ZSZhen Shang
Zhen Shang
Yao SunYao Sun
Yao Sun
XYXiumin Yu
Xiumin Yu
LHLing He
Ling He
LRLuquan Ren
Luquan Ren
To utilize the high efficiency of gasoline direct injection (GDI) and solve the high particulate number (PN) issue, hydrogen-rich syngas has been adopted as a favorable sustainable fuel. This paper compares and analyzes the effects of the injection configurations (GDI, gasoline port injection combined with GDI (PGDI), and gasoline port injection combined with hydrogen-rich syngas direct injection (PSDI)) and fuel properties on combustion and emissions in a spark-ignition engine. The operational points were fixed at 1800 rpm with a 15% throttle position, and the excess air ratio was 1.1. The conclusions show that PSDI gained the highest maximum brake thermal efficiency (BTE) at the MBT point, and the maximum BTE for GDI was only 94% of that for PSDI. PSDI’s CoVIMEP decreased by 22% compared with GDI’s CoVIMEP. CO and HC emissions were reduced by approximately 78% and 60% from GDI to PSDI among all the spark timings, respectively, while PSDI emitted the highest NOX emissions. As for particulate emissions, PSDI emitted the highest nucleation-mode PN, while GDI emitted the lowest. However, the accumulation-mode PN emitted from PSDI was approximately 52% of that from PGDI and 5% of that from GDI. This study demonstrates the benefits of PSDI for sustainability in vehicle engineering.

18 July 2023 in Case Studies in Thermal Engineering
Verified
Journal Article
Open access
ZZZhe Zhao
Zhe Zhao
YHYan Huang
Yan Huang
ZSZhen Shang
Zhen Shang
XYXiumin Yu
Xiumin Yu
PSPing Sun
Ping Sun
ZLZiyuan Li
Ziyuan Li

9 March 2023 in Journal of Materials Science
Verified
Journal Article
Open access
PDF file
HWHuan Wang
Huan Wang
ZLZiyuan Li
Ziyuan Li
ZSZhen Shang
Zhen Shang
LTLimei Tian
Limei Tian
Porous ceramics have a wide range of applications in areas such as energy storage, heat transfer and sewage treatment. One of the common preparation methods of porous ceramics is photocuring 3D printing technology. However, many cracks inevitably appear on the surface of the porous ceramic skeleton after sintering. These cracks impair the mechanical properties and thermal conductivity of the porous ceramic skeleton, accelerate its corrosion rate, and limit its engineering applications. Therefore, methods to repair cracks on the surface of porous ceramics are urgently required. In this work, the green body of the porous ceramic skeleton was prepared by a liquid crystal display 3D printer. Two kinds of porous ceramic skeleton were prepared, either by high-temperature sintering in an inert atmosphere or by liquid silicon infiltration. The cracks on the surface of the two kinds of porous ceramic skeleton were repaired by impregnation followed by secondary sintering. After secondary sintering, a porous ceramic skeleton with superior performance was obtained. Experimental results showed that the porosity of porous ceramic skeleton after high-temperature sintering in an inert atmosphere and liquid silicon infiltration was 76.39% and 72.30%, respectively. After the crack repair, the porosity of porous ceramic skeleton decreased by 4.64% and 4.33%, respectively. However, the compressive stress of the porous ceramic skeleton increased by 12.78 times and 4.56 times, and the heat transfer efficiency increased by 15.38% and 12.12%, respectively. Therefore, this study provides a method for crack repair on the surface of ceramic skeletons, which is of great significance for the improvement of mechanical properties and thermal conductivity of the porous ceramic skeleton.

21 September 2026 in Nano Letters
Verified
Journal Article
Closed access
XZXueli Zhou
Xueli Zhou
RZRuidan Zhang
Ruidan Zhang
YCYansong Chen
Yansong Chen
ZQZhihui Qian
Zhihui Qian
Liu QingpingLiu Qingping
Liu Qingping
LRLuquan Ren
Luquan Ren