While the employment of wide bandgap (WBG) devices in high-frequency and high-voltage applications brings benefits such as reduced system size and improved efficiency, it aggravates the electromagnetic interference (EMI) issue due to fast switching. High-frequency EMI noise suppression relies mainly on the filter design, where the filter's performance is strongly affected by parasitics. Through analyzing the common-mode (CM) equivalent circuit of a half-bridge power module, this letter identifies the key parasitics that dominate the performance of a common-mode filter (CMF) at high frequencies. To minimize the parasitics, the concept of integrating the CMF inside the WBG power module package is developed to improve the noise attenuation. A π-type CMF is integrated with a half-bridge GaN-based power module as a prototype to validate the concept. Experiments are conducted by measuring the CM noise spectrum received by the line impedance stabilization networks (LISNs) from the hard switching of the designed power module under 70 V and 80 kHz. Comparing the measured results of the integrated CMF to the externally-added CMF, up to 50 dBμV more attenuation is achieved by the integrated CMF in the frequency range of 10 MHz to 100 MHz, verifying the theoretical analysis and the established CM equivalent circuit.
30 September 2024 in IEEE Open Journal of Power Electronics
This paper summarizes the main results and contributions of the MagNet Challenge 2023, an open-source research initiative for data-driven modeling of power magnetic materials. The MagNet Challenge has (1) advanced the stateof-the-art in power magnetics modeling; (2) set up examples for fostering an open-source and transparent research community; (3) developed useful guidelines and practical rules for conducting data-driven research in power electronics; and (4) provided a fair performance benchmark leading to insights on the most promising future research directions. The competition yielded a collection of publicly disclosed software algorithms and tools designed to capture the distinct loss characteristics of power magnetic materials, which are mostly open-sourced. We have attempted to bridge power electronics domain knowledge with state-of-the-art advancements in artificial intelligence, machine learning, pattern recognition, and signal processing. The MagNet Challenge has greatly improved the accuracy and reduced the size of data-driven power magnetic material models. The models and tools created for various materials were meticulously documented and shared within the broader power electronics community.
24 January 2024 in IEEE Open Journal of Power Electronics
The wide applications of wide-bandgap (WBG) devices in power electronics systems bring benefits in higher switching speed, frequency, and power density, but also cause severe electromagnetic interference (EMI) issues. While many EMI mitigation methods are available to reduce the noise generated from the source (i.e. switching WBG devices), it is equally important to analyze and control the EMI propagation paths. In WBG systems, the parasitic and coupling effects become dominant due to the high switching frequency and the compact system size, which creates uncontrolled propagation paths that degrade the systems' EMI performance significantly. Therefore, it is crucial to investigate the parasitic and coupling effects and develop corresponding mitigation techniques. This review focuses on analyzing the EMI propagation paths to provide a comprehensive guideline to identify possible parasitics and couplings in the power module package level, EMI filter level, and the power electronics system level. The corresponding mitigation techniques for common-mode and differential-mode conducted EMI as well as radiated EMI are summarized, and the remaining challenges and future research topics are also discussed for all three levels in the conclusion.
5 September 2023 in IEEE Transactions on Power Electronics
Lateral gallium nitride (GaN) high-electron-mobility transistors present better electrical characteristics compared to silicon or silicon carbide devices such as high switching speed and low gate charge, but also present additional challenges on the module design. This article discusses a high-density GaN power module with double-sided cooling, low inductance, on-package decoupling capacitors, and integrated gate drivers. The GaN dies as well as the gate drive are sandwiched between the printed circuit board and direct bonded copper substrate to achieve compact loop and double-sided cooling effect. Design considerations and thermal performance are analyzed. A module assembly procedure is presented utilizing the layer-by-layer attachment process. Finally, a 2.7 cm × 1.8 cm half-bridge GaN power module is fabricated and tested, achieving a low power-loop inductance of 1.03 nH, and the overshoot voltage of the switching waveform is less than 5% under a 400 V/25 A double-pulse test. The thermal resistance is 0.32 K/W, verified by simulation and experimental results. The design and assembly process can be generalized and applied to high power applications to achieve high power density and high performance.
13 June 2019 in IEEE Transactions on Microwave Theory and Techniques
A physics-based nonlinear circuit model is developed for frequency-selective limiters (FSLs) based on thin-film magnetic materials. The equivalent circuit model is structured and its parameters are determined rigorously from the fundamental physics of electromagnetic waves and spin waves. The spin motions as well as the ferromagnetic resonance (FMR) are modeled by RLC parallel circuits with parameters derived from Polder's tensor and Kittel's equations. The exchange coupling between spins is modeled by an inductor added between adjacent RLC circuits based on quantum spin theory. The nonlinear crossfrequency coupling from signal at ω to spin waves at ω/2 is represented by a nonlinear coupled inductor model that follows the mathematics of a pendulum motion to represent the parametric oscillations of spins. The circuit units are cascaded to describe the spin-wave propagation inside the magnetic material, and transmission line parameters are added finally to describe the electromagnetic wave propagation. An FSL device described in the literature is used as an example to validate the circuit model, and the model successfully predicts the power-dependent insertion loss as well as the threshold power level, time delay, and frequency selectivity of the power limiting effect.
24 June 2021 in IEEE Transactions on Antennas and Propagation
It is proposed that ferromagnetic resonance (FMR) of thin-film ferrites can be utilized to simultaneously improve the radiation efficiency and input impedance matching of electrically small antennas (ESAs). To validate the concept, the role of FMR in radiation is first derived analytically with an ideal thin-film ferrite radiator. It was concluded that the Gilbert damping of the ferrite, determining the quality factor of FMR, directly impacts on the radiation efficiency of the antenna. A practical example is proposed in the form of an electrically small single-loop antenna loaded with a thin-film yttrium-iron-garnet (YIG) core. The prototype has been designed, fabricated, and evaluated through both full-wave simulations and experiments. The simulation results match well to the experimental results, demonstrating the efficacy and significance of the idea. In addition, broadband equivalent circuit models are derived to model both the electrically small loops with and without the FMR enhancement and to provide additional insights into the design. The circuit models prove to be effective in predicting the input impedance and radiation efficiency of FMR-enhanced ESAs at a precision comparable with full-wave simulations.