26 July 2021 in IEEE Access
Solid-state power controllers (SSPCs) have been received increasing attention as they can configure the electrical system and protect the system by fast tripping mechanism at the same time. Although the high-voltage direct current (HVDC) electrical system can bring sustainable savings on the cables' weight and losses, the protection can be considerably challenging. SSPCs have been successfully utilized for 28V DC aircraft onboard network. However, high-voltage ones are impeded by the vast over-voltage and the excessive losses generated from SSPC switching. This paper tries to fill this gap and presents the development of high-power SSPCs for a ±270VDC network of a future turboprop aircraft. Comprehensive designs of proper over-voltage suppression along with SSPC thermal management are presented in this paper. Besides, a comparative study on the SSPC device is carried out. Two prototypes, including a single MOSFET module and paralleling several discrete MOSFET devices, are built and then tested in the experiment. It has been validated that the proposed voltage clamping design cannot only effectively suppress the over-voltage, but also limit the SSPC temperature increase during switching for both candidates. After comparing the conduction losses, maximum junction temperature, power density, weight and volume, the single device solution is recommended as a preferable SSPC option for future aircraft.
29 June 2021 in IEEE Transactions on Transportation Electrification
This article presents a control scheme for a recently reported aircraft advanced power generation center (APGC) during postfault operation conditions. Within the APGC, two electrical generators extract power from two separate engine shafts and supply electrical power to a common high-voltage direct current (HVDC) bus through their dedicated main ac/dc power converters. An extra back-to-back (BTB) converter is also used to connect the ac terminals of the two generators. This architecture provides merits of fault tolerance capabilities of the APGC. In the case of main ac/dc power converter failure, the system can be reconfigured and the BTB converter provides an extra power flow path from the generators to the HVDC bus. This ensures electrical power generation capabilities onboard. This article discusses in detail about the control of the APGC under fault conditions with one main ac/dc converter failure. A seamless transition scheme from normal operation to postfault conditions is proposed using a voltage command initialization technique within the BTB converter. Both experimental and simulation results have verified the fault tolerance improvement and control performances of the APGC.
4 May 2021 in IEEE Transactions on Industrial Electronics
This article proposed a harmonic suppression scheme that used a dc-dc converter as an active harmonic injector to cancel voltage harmonics on the HVdc bus within a hybrid power generation centre (HPGC). A permanent magnet synchronous generator and a battery are considered to supply power to a common HVdc bus through their dedicated ac-dc and dc-dc converters respectively within the HPGC. We proposed simplified mathematical models of harmonics from the ac-dc and dc-dc converters. Thereafter, an active power sharing scheme between the PMSG and the battery is developed to control the magnitudes of targeted harmonics to be the same. The targeted harmonics on the HVdc bus can thus be cancelled by properly tuning the carrier signal phase angles within ac-dc and dc-dc converters. A closed-loop control scheme has been developed and this scheme is with no extra hardware cost. To demonstrate the effectiveness of the proposed scheme, we selected the first-band harmonic ( fc − 3 f0 ) as the targeted harmonic component. The harmonic cancellation scheme for this component has been developed and validated using experimental results. It has been demonstrated that the proposed method can achieve over 90% reduction of this specific harmonic component on the HVdc bus within this HPGC using one dc-dc converter.
3 May 2023 in IEEE Transactions on Transportation Electrification
The design of the droop coefficient is one of the challenges for the droop control of converters, as it plays a key role in enhancing the performance of the droop control method. This paper proposes an artificial neural network (ANN) based technique for the design of optimal droop control of parallel-connected converters in a fast and accurate manner, without imposing an additional computational burden on the system. The developed ANN-based design strategy of droop coefficients is used for load sharing and DC bus voltage regulation for the more electric aircraft application. In the design process, the optimal droop coefficient setting is obtained by evaluating a user-defined fitness function with the aid of a trained ANN-based surrogate model. It is observed that the system performance metrics predicted by the surrogate model matched very well with that obtained from the simulation model. The experimental results show that the selected optimal droop coefficient setting can enhance the performance of the traditional droop control method in both steady and transient conditions.
3 August 2021 in IEEE Transactions on Industrial Electronics
Harmonics generated from power electronic converters will impose significant power quality challenges to the electric grid onboard future aircraft. In this article, we propose an innovative modulation scheme that enables using a buck–boost dc–dc converter as a harmonic absorber. To demonstrate the effectiveness of the proposed method, a hybrid power generation system involving a high-speed electrical generator and a high voltage battery is introduced. The electrical generator is connected to a dc bus through an ac–dc converter and the battery to the dc bus with a dc–dc converter. For the studied hybrid power generation system, it is identified that the first carrier frequency side-band harmonic ( fc -3 f0 ) from the ac–dc converter is most relevant and is targeted for cancellation. For the control of the dc–dc converter, a new modulation technique, called equal-gate-width modulation is proposed. It allows active control of the magnitude and phase angle of some specific harmonic components from a dc–dc converter. By properly tuning the phase angle and amplitude, the controlled harmonics can thus be used to cancel harmonics from other converters on a common dc bus. Without losing generality, this article focuses on the development of this specific harmonic cancellation scheme and the effectiveness of our proposed methods has been demonstrated using experimental results.
7 July 2021 in IEEE Transactions on Transportation Electrification
In the high-power settings of engine, such as maximum take-off, more power should be extracted from the high-pressure spool of engine (HPS) than the low-pressure spool of engine (LPS) to avoid the overspeed and potential instability of the HPS. However, as revealed in this article, extracting more power from the HPS will degrade the onboard high-voltage direct current (HVdc) grid stability for the conventional single dc bus power generation center. To address this conflict, in this article, an advanced power generation center (APGC) incorporating an extra back-to-back (BTB) converter is introduced to improve the stability for both engine and HVdc grid. The BTB converter connects the HP power generation channel and the LP channel, providing an additional power flow path between the HP channel and LP channel. A transfer function-based impedance model and a state-space model of the HVdc grid are proposed to study the HVdc grid stability. The analytical findings of the HVdc grid stability and stability improvement using the APGC architecture have been verified through simulation and experimental results.