15 October 2019 in Journal of Geophysical Research: Planets
18 May 2022 in Journal of Geophysical Research: Planets
Analyses of seismic data from the InSight mission have provided the first in situ constraints on the thickness of the crust of Mars. These crustal thickness constraints are currently limited to beneath the lander that is located in the northern lowlands, and we use gravity and topography data to construct global crustal thickness models that satisfy the seismic data. These models consider a range of possible mantle and core density profiles, a range of crustal densities, a low‐density surface layer, and the possibility that the crustal density of the northern lowlands is greater than that of the southern highlands. Using the preferred InSight three‐layer seismic model of the crust, the average crustal thickness of the planet is found to lie between 30 and 72 km. Depending on the choice of the upper mantle density, the maximum permissible density of the northern lowlands and southern highlands crust is constrained to be between 2,850 and 3,100 kg m−3. These crustal densities are lower than typical Martian basaltic materials and are consistent with a crust that is on average more felsic than the materials found at the surface. We argue that a substantial portion of the crust of Mars is a primary crust that formed during the initial differentiation of the planet. Various hypotheses for the origin of the observed intracrustal seisimic layers are assessed, with our preferred interpretation including thick volcanic deposits, ejecta from the Utopia basin, porosity closure, and differentiation products of a Borealis impact melt sheet.
9 October 2020 in Science Advances
Heterogeneous thermal properties of Bennu are due primarily to spatial mixing of two boulder types with differing strengths.
31 July 2019 in Journal of Geophysical Research: Planets
The thermophysical properties of lunar regolith have been thoroughly investigated for temperatures higher than 100 K. For the near‐equatorial thermal measurements of the Apollo era, this temperature range was sufficient to generate appropriate models. However, recent measurements from the Lunar Reconnaissance Orbiter Diviner Lunar Radiometer Experiment have revealed polar temperatures as low as 20 K, with apparently lower thermal inertia than explainable by existing theory. In the absence of comprehensive laboratory measurements of regolith thermal properties at low temperatures (<100 K), we investigate solid state theory and fits to lunar simulant materials to derive a semiempirical model of specific heat and thermal conductivity in lunar regolith in the full range 20–400 K. The primary distinctions between these previous models are (1) the temperature dependence of the solid conduction component of thermal conductivity at low temperatures, (2) the focus on regolith bulk density as the primary variable, and (3) the concept that the composition and modal petrology of grains could significantly influence thermal properties of the bulk regolith. This model predicts that at low temperatures, thermal conductivity is as much as an order of magnitude lower and specific heat is likely higher than expected from current models. The thermal conductivity at low temperature should vary depending on the constituent grain materials, their crystallinity, contributions from phonon scattering modes, bulk porosity, and density. To demonstrate the impact of our finding, we extrapolate the effects of our conductivity model on temperature variations in permanently shadowed regions on the Moon. This work motivates experimental confirmation of thermophysical properties of lunar regolith at low temperature.
26 August 2022 in Science Advances
The Radar Imager for Mars Subsurface Experiment instrument has conducted the first rover-mounted ground-penetrating radar survey of the Martian subsurface. A continuous radar image acquired over the Perseverance rover’s initial ~3-kilometer traverse reveals electromagnetic properties and bedrock stratigraphy of the Jezero crater floor to depths of ~15 meters below the surface. The radar image reveals the presence of ubiquitous strongly reflecting layered sequences that dip downward at angles of up to 15 degrees from horizontal in directions normal to the curvilinear boundary of and away from the exposed section of the Séitah formation. The observed slopes, thicknesses, and internal morphology of the inclined stratigraphic sections can be interpreted either as magmatic layering formed in a differentiated igneous body or as sedimentary layering commonly formed in aqueous environments on Earth. The discovery of buried structures on the Jezero crater floor is potentially compatible with a history of igneous activity and a history of multiple aqueous episodes.
3 January 2020 in Journal of Geophysical Research: Planets
We derive a new constraint on the thermal and dielectric properties of the lunar regolith layer by reconciling data from the Lunar Reconnaissance Orbiter (LRO) Diviner infrared radiometer and Chang'E‐2 (CE‐2) microwave radiometer (MRM). The bolometric Bond albedo of the lunar surface, which characterizes the ability of the lunar surface to reflect visible radiation, is a function of incidence angle. We determined the Bond albedo by using the Lunar Orbiter Laser Altimeter 1,064‐nm normal albedo and the surface temperature at noon as a function of latitude. The results suggest a modification to existing regolith thermal conductivity models based on a fit to the diurnal variation of Diviner data. Based on the thermal model, a 1‐D radiative transfer and dielectric properties model is developed to fit MRM data for the global Moon. With a new dielectric loss tangent equation for highland regolith applied, our model matches MRM data well at 19.35 and 37 GHz, which are generally accepted to be well calibrated. A global map of loss tangent of the Moon at these frequencies is also obtained by fitting the diurnal amplitude of microwave brightness temperature (TB) of each location on the Moon. We find that the loss tangent of highlands regolith has a slight frequency dependence and is larger than previous studies. We also identify a large discrepancy between our theoretical model and TB obtained by CE‐2 MRM at low frequencies, which is attributed to issues caused by contamination on calibration horn.