In this work, we presented the design and simulation of a new flux-controlled meminductor emulator based on a modified version of the well-known Antoniou’s inductor simulator circuit. The constitutive theoretical equations of meminductance are presented and subsequently correlated with the electrical behavior of Antoniou’s circuit, hence illustrating its practical meminductive behavior with a proper selection of feedback impedances. After that, the feasibility of a practical implementation using off-the-shelf devices is illustrated firstly for a two-state meminductor and secondly for a continuous-state meminductor by means of SPICE simulations. It was also demonstrated that this emulator can operate at different frequencies and input signals constituting one of the simplest and most versatile meminductor emulators to date.
3 May 2021 in IEEE Transactions on Power Electronics
In this article, a power converter based on an asymmetrical half-bridge flyback topology is analyzed and optimized for small form factor and fast-charging power adaptors. Two resonant control methods, taking advantage of the forward and flyback characteristics of the converter, as well as the benefits of each of them depending of the operation point are discussed. The analysis is nourished with the equivalent circuits in each phase of operation and the equations that define them. Particularly innovative is the proposed zero voltage resonant valley switching control method for the mentioned converter; in this case, it is operated similarly to a flyback converter, allowing safe output voltage ramp up, which is one of the challenges that has limited the usage of this topology up to now. The manuscript also describes how to achieve high efficiency and power density using zero-voltage switching and zero-current switching techniques over the full range of the input voltage and the output load. Finally, the advantages of the proposed control methods are demonstrated in a 65-W adaptor prototype achieving a peak efficiency over 94.6% and an efficiency of 93.8% @ V ac ≥ 100 V at full load over the range of the input voltage, as well as a world-class power density of 35 W/in 3 uncased.
The recent release of the standard USB-PD 3.1 [1] specifies variable output voltages from 5 V to 48 V featuring a step forward towards a universal adaptor but rising new challenges for the converter topologies used up to now. In such applications, a first AC-DC stage is followed by a DC-DC stage. In this paper, emerging WBG technologies are applied to the asymmetrical half-bridge flyback topology, demonstrating the potential of such combination as a wide voltage range DC-DC stage. Its suitability for high-density and high-efficiency USB-PD Extended Power Range (EPR) and battery charger applications is discussed. The impact of different switching technologies, silicon and wide band gap, is analyzed. A general method to dimension the converter is presented and an iterative process is used to evaluate the theoretical efficiency under different conditions and switching devices. Finally, the advantages of the presented converter using Gallium Nitride (GaN) devices are demonstrated in a 240 W DC-DC prototype. It achieves a full load efficiency of 98%, and it is able to deliver an output voltage from 5 V to 48 V with input voltage range from 120 V to 420 V, as well an outstanding power density of 112 W/inch3 uncased.
In this article, an innovative power adaptor based on the asymmetrical pulse width modulation (PWM) flyback topology will be presented. Its benefits compared to other state-of-the-art topologies, such as the active clamp flyback, are analyzed in detail. It will also describe the control methods to achieve high efficiency and power density using zero-voltage switching (ZVS) and zero-current switching (ZCS) techniques over the full range of the input voltage and the output load, providing comprehensive guidelines for the practical design. Finally, we demonstrate the convenience of the proposed design methods with a 65 W adaptor prototype achieving a peak efficiency of close to 95% and a minimum efficiency of 93.4% at full load over the range of the input voltage, as well as a world-class power density of 22 W/inch3 cased.
This paper presents a low-cost, self-recoverable, double-node upset tolerant latch aiming at nourishing the lack of these devices in the state of the art, especially featuring self-recoverability while maintaining a low-cost profile. Thus, this D-latch may be useful for high reliability and high-performance safety-critical applications as it can detect and recover faults happening during holding time in harsh radiation environments. The proposed D-latch design is based on a low-cost single event double-node upset tolerant latch and a rule-based double-node upset (DNU) tolerant latch which provides it with the self-recoverability against DNU, but paired with a low transistor count and high performance. Simulation waveforms support the achievements and demonstrate that this new D-latch is fully self-recoverable against double-node upset. In addition, the minimum improvement of the delay-power-area product of the proposed rule-based design for the low-cost DNU tolerant self-recoverable latch (RB-LDNUR) is 59%, compared with the latest DNU self-recoverable latch on the literature.
15 September 2025 in IEEE Transactions on Power Electronics
As the demand for more efficient and compact power converters grows, the trend points to a progressive raise of their switching frequency. However, even with wide-bandgap semiconductors, switching losses limit the maximum frequency at which they can operate, requiring zero-voltage switching (ZVS) to maximize efficiency and to prevent overheating. Existing studies state that the conditions to achieve ZVS depend only on the stored charge in the output parasitic capacitances of the transistors, but this statement is not applicable for the asymmetrical half-bridge (AHB) structure defined in this article, commonly found in topologies such as the buck and the asymmetrical half-bridge flyback. This article addresses this limitation by deriving a novel condition for achieving complete ZVS in the AHB, showing that both, the stored charge and the stored energy in the transistors must be considered. It also proposes a simplified circuit for analyzing dead times and discusses the issue of having different switches in a half-bridge, stating the advantage of placing high capacitance transistors in the low-side. Furthermore, this article proposes some consideration for dimensioning the converter that facilitate achieving ZVS. Experimental measurements validate the theoretical analysis, demonstrating its potential in the design of high efficiency and high power density converters.