Kristina Ancutiene

Kristina Ancutiene

Auto-generated profile, based on publicly available information

Kristina Ancutiene

Department of Production Engineering, Kaunas University of Technology, Kaunas, Lithuania

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 November 2019 in International Journal of Clothing Science and Technology
Verified
Journal Article
Closed access
ALAgnė Lagė
Agnė Lagė
KAKristina Ancutienė
Kristina Ancutienė
Purpose: The purpose of this paper is to investigate basic block pattern modification according to fabric used and the mismatch between 2D and 3D measure lines at bust, waist and hip girths when ease allowance is changed uniformly. Design/methodology/approach: For the investigation, virtual try-on software Modaris 3D Fit (CAD Lectra) was used. The straight shape dress fitting was done using seven cotton and cotton blended plain weave fabrics. After virtual try-on, the mismatch d (dbust, dwaist, dhip) between 2D and 3D measure lines was measured in order to determine base pattern adjustments using different fabrics. Findings: It was found that the position and length of 3D measure lines at bust, waist and hip girths does not match the position and length of corresponding lines in 2D base patterns after virtual try-on due to fabrics deformation, which is related to mechanical properties. It was proved that derived linear equations presenting a relation between mismatch and ease allowance values could be used for basic block pattern modification that 3D and 2D measure lines would coincide during clothing try-on. Research limitations/implications: This research is limited to cotton/cotton blended woven fabrics and straight dress; therefore, other fabric types and other clothing could be investigated in the future to expand data basis. Practical implications: The main practical point of the proposed method is that in order to obtain particular 3D ease value in a garment, it can be calculated from 2D ease allowance value and the fabric’s tensile properties using linear equations. The basic block patterns could be modified using this method not only for tested fabrics but also for other fabrics with similar composition, structural and mechanical properties. 3D ease values in garment can be easily checked by using virtual try-on technology without production of real prototypes. The method is applicable for making ready-to-wear or individually tailored clothing. Originality/value: The proposed method in this paper presented opportunity to modify the basic block patterns of the dress according to the fabric’s tensile properties and 2D ease allowance. The basic block patterns could be modified according to presented linear functions for each tested fabric. The application of this method can fully ensure the interaction between the garment 2D patterns to 3D garment so that a desired 3D garment fitting effect to the body can easily be satisfied by the adjustment of particular fabric characteristics. It offers further possibilities, especially with developing virtual try-on technologies.

2 February 2017 in The Journal of the Textile Institute
Verified
Journal Article
Closed access
ALAgne Lage
Agne Lage
KAKristina Ancutiene
Kristina Ancutiene
The aim of the first part of the research was to investigate distance ease distribution between straight shape virtual dress and 3D body in respect to fabrics mechanical (tensile, bending, shear) properties using virtual try-on software Modaris 3D Fit (CAD Lectra). The second part would be intended for the basic construction adjustment according to the mechanical properties of textile materials. The objects of the investigations were 100% cotton and cotton-blended plain weave fabrics. Mechanical properties were defined by KES-F (Kawabata). Virtual mannequin was covered with straight virtual dress. Distance ease distribution as well as the values of simulated 3D garment at bust girth ES3D_bust (cm) were investigated. It was defined that distance ease in 3D garment was lower than ease allowance used for 2D basic construction. The strongest effect upon the distance ease between body and garment had tensile strain of fabrics in weft direction.

17 June 2018 in Journal of Industrial Textiles
Verified
Journal Article
Closed access
JKJulija Krauledaitė
Julija Krauledaitė
KAKristina Ancutienė
Kristina Ancutienė
VUVirginijus Urbelis
Virginijus Urbelis
SKSigitas Krauledas
Sigitas Krauledas
VSVirginija Sacevičienė
Virginija Sacevičienė
In this research, eight different 3D weft-knitted fabrics were developed and evaluated. 3D fabrics have been knitted on circular weft-knitting machines with two different gauges: 20E gauge and 28E gauge. Three different raw materials were used for the fabric’s production: high molecular mass polyethylene (HPPE) yarn and 0.05 mm diameter steel wire in the outer layers (for the front and reverse) and polyamide yarn in the binding layer. The experiments were conducted on the developed 3D knitted fabrics to determine the fabric’s resistance to mechanical risks such as circular blade cut, puncture, abrasion, and also to evaluate the comfort parameter, such as air permeability. It was defined that 3D weft-knitted fabrics best results on tests: circular blade cut, puncture and abrasion resistant were achieved using HPPE yarn twisted with steel wire, higher mass per unit area with more significant amount of steel wire. According to the standard EN 388:2003, three samples of developed 3D weft-knitted fabrics had the highest 5th blade cut and the highest (4th) abrasion resistance level. All of them had the highest (4th) level of puncture resistance. 3D fabrics knitted on a circular weft-knitting machine of gauge 28E ensured 1.3–2.1 times greater blade cut and 4.9–12.1 times greater abrasion resistance result, than fabrics knitted on gauge 20E, due to a higher stitch density, higher mass per unit area, density and fabric’s thickness. But on the other hand, these parameters lowered air permeability by 20.2–43.0%.

4 July 2011 in Materials Science
Verified
Journal Article
Open access
PDF file
KAKristina Ancutienė
Kristina Ancutienė
DSDovilė SINKEVIČIŪTĖ
Dovilė SINKEVIČIŪTĖ
3D virtual representation of garment provides high potential for design, product development and marketing processes, especially in mass customization strategies implementation. Clothing industry rapidly turns to virtual simulation which not only presents realistic 3D view of garment but also simulates mechanical behaviour of materials. 3D CAD systems can be used to define strain distribution in virtual garment which describes garment fit without actually producing the garment. Strain and distance ease between body and garment depends not only upon body measurements and garment construction, but also on mechanical and structural properties of selected material. The aim of this research was to investigate virtual garment fit using "Modaris 3D Fit" (Lectra) software subjected to fabrics mechanical (tensile, bending, shear) and structural (composition, thickness, area density) properties investigating strain distribution in garment and distance ease between garment and human body. It was defined that for diagonal cut garments the highest influence upon garment fit has fabric tensile properties in weft direction. The highest influence is obtained at high distance ease and small strain values zones and at negative distance ease and high strain values zones. Therefore, presented method could be used for tight-fitted garments also for garments with draperies on purpose to investigate garment fit upon fabrics used.http://dx.doi.org/10.5755/j01.ms.17.2.486

23 May 2023 in International Journal of Clothing Science and Technology
Verified
Journal Article
Closed access
KLKestutis Lekeckas
Kestutis Lekeckas
JSJulija Stirbe
Julija Stirbe
KAKristina Ancutiene
Kristina Ancutiene
RVRuta Valusyte
Ruta Valusyte
Purpose: To explore the influence of various factors on the adhesion strength of 3D printing materials and chiffon fabrics, and to develop an original design clothing prototype with an extended functionality that would be compatible with the specifics of the circular design.Design/methodology/approach: Four different chiffon fabrics and four 3D printed materials were chosen as the research subjects to determine the influence of various factors on the adhesion strength and ductility. The uniaxial tensile test was used to determine pull-out force and the pull-out elongation from the interlayer.Findings: 3D printed TPU elements can be used to join clothing parts made from low-elasticity chiffon fabrics to improve wearing comfort. In order to comply with the circular economy concept, it is important to select such adhesion parameters of the 3D printed elements and the material system that would ensure wear comfort and withstand wear-level loads; and at the end of the life cycle of a garment, the 3D printed elements could be separated from the product and recycled.Originality/value: The systems developed can be used to renew and repair products, adding originality, individual touch or additional decorative features, while extending the functional possibilities of clothing items in accordance with circular design principles.

30 September 2013 in The Journal of the Textile Institute
Verified
Journal Article
Closed access
KAKristina Ancutiene
Kristina Ancutiene
ESEugenija Strazdiene
Eugenija Strazdiene
KLKestutis Lekeckas
Kestutis Lekeckas