Solid waste is one of the leading environmental problems affecting human lives. Selecting a landfill where waste is disposed of is a complicated issue that related to many factors and regulations. In this study, the optimal sanitary landfill site for An-Najaf city was assessed using the GIS and weight criteria method. Eight appropriate criteria were selected, which are: urban area, rivers, roads, soil types, elevation, wind, slope, and archaeological, historical and religious sites. Moreover, the weighting of the criteria by using experts’ opinion and previous similar literature. The “weighted overlay tool” is then applied to get a map of the significance index for selected landfill sites. Seven suitable sites with an area of 177,762,986 m2 and form 0.62% from the total city area can accommodate the solid waste generated for a period, not less than ten years10 years.
30 September 2020 in Iraqi Journal of Chemical and Petroleum Engineering
In this study, the circulating fluidized bed was used to remove the Tetracycline from wastewater utilizing a pistachio shell coated with ZnO nanoparticles. Several parameters including, Tetracycline solution flowrate, initial static bed height, Tetracycline initial concentration and airflow rate were systematically examined to show their effect on the breakthrough curve and the required time to reach the adsorption capacity and thus draw the fully saturated curve of the adsorbent. Results showed that using ZnO nanoparticles will increase the adsorbent surface area and pores and as a result the adsorption increased, also the required time for adsorbent saturation increased and thus the removal efficiency may be achieved at minimum antibiotic flowrate, maximum bed height, higher antibiotic concentration, and higher airflow rate. Also, a minimum fluidization velocity correlation was developed in this study. This correlation was found to be a function of liquid velocity, bed height, particle size, and particle density. The results showed that circulating fluidized bed has a better performance and last more than two hours before the bed biomass exhausted in comparison with traditional fluidized bed.
The Environmental Impact Assessment (EIA) procedure is designed to identify and predict the impacts of bio-geophysical environments on human health. In this study, the Leopold matrix was applied to predict the pollution impacts of seven water projects in Karbala city in Iraq based on water quality data collected for the period January to December 2018. The results showed that the impacts of Ca and SO4 in treated water were unacceptable in most cases due to uncontrolled dosage of alum and lime added during water treatment processes. The results also demonstrated that the maximum environmental impact (EIV) for raw water was 51.21 at Al-Hendiya Al-Qadeem water treatment plant (WTP) while that for treated water was 99.97, at Hay Al-Hussein WTP. The obtained impact values of treated water quality parameters in this study occurred due to the use of old techniques in water treatment and demonstrate the need to upgrade these techniques. The Leopold matrix was, however, shown to be good process for sifting out or mitigating the negative effects of such projects on humans and the environment.
16 September 2022 in Journal of Applied Water Engineering and Research
In this study, four types of adsorbents were examined for their ability to remove methylene blue MB from aqueous solution by adsorption in a fixed bed system. The adsorbents used were activated carbon (AC), manufactured activated carbon (ACPP1), chemically activated carbon with nitric acid (10% wt) (ACPP2), and with nitric acid and H2SO4 (ratio 1:1) (ACPP3). 28 experiments were conducted to test the effect of MB concentrations, adsorbent bed depth, and solution flow rate. Langmuir and Freundlich as isotherm models were analyzed by nonlinear regression. For AC and ACPP1 the adsorption occurred under heterogeneous and multilayer surfaces. Conversely, for ACPP2 and ACPP3 adsorbent, homogeneous and monolayer control adsorption of MB on this adsorbent and maximum adsorption capacity was 33.149 and 38.508 mg/g for MB onto ACPP2 and ACPP3, respectively. The effect of the flow rate (132,200 and 250 cc/min), bed height (0.05, 0.1, and 0.15 m), and initial MB concentration (150, 300, and 500 mg/l) on the performance of the breakthrough curves were clarified. The Bohart-Adams and Thomas-BDST models have a better correlation in relation to the analysis of fixed bed data.