We present a synthetic adaptation of the fibrillar adhesion surfaces found in nature. The structure consists of protruding fibrils topped by a thin plate and shows an experimentally measured enhancement in adhesion energy of up to a factor of 9 over a flat control. Additionally, this structure solves the robustness problems of previous mimic structures and has preferred contact properties (i.e., a large surface area and a highly compliant structure). We show that this geometry enhances adhesion because of its ability to trap interfacial cracks in highly compliant contact regimes between successive fibril detachments. This results in the requirement that the externally supplied energy release rate for interfacial separation be greater than the intrinsic work of adhesion, in a manner analogous to lattice trapping of cracks in crystalline solids.
We report a new dry adhesive structure using a rippled poly(dimethylsiloxane) (PDMS) elastomer bilayer film, whose surface roughness and adhesion can be reversibly regulated by applying mechanical strain. It has a set of advantages not offered by other techniques for regulation of adhesion, including real-time tunability, no requirement of specific surface chemistry, operability under ambient conditions, and relative ease of control. To understand the mechanism for adhesion regulation quantitatively, we have modeled the mechanics of adhesion in the limits of small- and large-amplitude ripples, and show good agreement with indentation experiments. We demonstrate the real-time tunability of the new adhesive structure by repeatedly picking and releasing a glass ball simply by modulating the mechanical stretch of the rippled PDMS film.
17 June 2019 in Proceedings of the National Academy of Sciences
Adhesives are ubiquitous in daily life and industrial applications. They usually fall into one of two classes: strong but irreversible (e.g., superglues) or reversible/reusable but weak (e.g., pressure-sensitive adhesives and biological and biomimetic surfaces). Achieving both superstrong adhesion and reversibility has been challenging. This task is particularly difficult for hydrogels that, because their major constituent is liquid water, typically do not adhere strongly to any material. Here, we report a snail epiphragm-inspired adhesion mechanism where a polymer gel system demonstrates superglue-like adhesion strength (up to 892 N⋅cm−2) that is also reversible. It is applicable to both flat and rough target surfaces. In its hydrated state, the softened gel conformally adapts to the target surface by low-energy deformation, which is locked upon drying as the elastic modulus is raised from hundreds of kilopascals to ∼2.3 GPa, analogous to the action of the epiphragm of snails. We show that in this system adhesion strength is based on the material’s intrinsic, especially near-surface, properties and not on any near-surface structure, providing reversibility and ease of scaling up for practical applications. Significance Achieving both superstrong adhesion and reversibility is challenging, particularly for hydrogels. Here, we report a hydrogel-based, reversible, superglue-like adhesive by combining the benefits of both liquid and dry adhesives in a single material while overcoming their respective limitations. When hydrated, the softened gel conformally adapts to the target surface by low-energy deformation, which is then locked upon drying as the elastic modulus is raised from hundreds of kilopascals to a few gigapascals, analogous to the action of the epiphragm of snails. We show that reversible superstrong adhesion could be achieved from a nonstructured material when the criterion of shape adaption is met, with minimal residual strain energy stored in the system.
Adhesives typically fall into two categories: those that have high but irreversible adhesion strength due to the formation of covalent bonds at the interface and are slow to deploy, and others that are fast to deploy and the adhesion is reversible but weak in strength due to formation of noncovalent bonds. Synergizing the advantages from both categories remains challenging but pivotal for the development of the next generation of wound dressing adhesives. Here, we report a fast and reversible adhesive consisting of dynamic boronic ester covalent bonds, formed between poly(vinyl alcohol) (PVA) and boric acid (BA) for potential use as a wound dressing adhesive. Mechanical testing shows that the adhesive film has strength in shear of 61 N/cm 2 and transcutaneous adhesive strength of 511 N/cm 2 , generated within 2 min of application. Yet the film can be effortlessly debonded when exposed to excess water. The mechanical properties of PVA/BA adhesives are tunable by varying the cross-linking density. Within seconds of activation by water, the surface boronic ester bonds in the PVA/BA film undergo fast debonding and instant softening, leading to conformal contact with the adherends and reformation of the boronic ester bonds at the interface. Meanwhile, the bulk film remains dehydrated to offer efficient load transmission, which is important to achieve strong adhesion without delamination at the interface. Whether the substrate surface is smooth (e.g., glass) or rough (e.g., hairy mouse skin), PVA/BA adhesives demonstrate superior adhesion compared to the most widely used topical skin adhesive in clinical medicine, Dermabond.