23 December 2016 in Journal of Vibration and Control
Joints with clearance always exist in steering mechanism of vehicles due to the machining tolerances, deformations and wear, which should not be neglected in modeling and analysis of vehicle shimmy system. Based on Lagrange equation method, a six-DOF dynamic model of vehicle shimmy system with consideration of multi-clearance joints was established. The model of movement pairs with clearance was built based on Hertzian contact law. The nonlinear cornering force of pneumatic tire was described based on PAC2002 tire model, and its parameters were obtained by an identification method based on experimental data. Then numerical examples were employed to evaluate the dynamic response of the shimmy system. The influence of multi-clearance joints on the response of shimmy was analyzed, and it is compared with that of one clearance joint. The acting mechanism of contact force between movement pairs was investigated, and global dynamic analysis was carried out by using point mapping method. Moreover, the dynamic mechanism for vehicle shimmy was investigated based on energy input. The conclusions can provide theoretic evidence for attenuation of vehicle shimmy, especially for those in-service vehicles.
3 July 2013 in Journal of Vibration and Control
Influences of system parameters on dynamic behavior of the vehicle shimmy system with consideration of clearance in the steering linkage mechanism are analyzed. The kinematic pair of steering linkage mechanism with clearance between the steering tie rod and left trapezoidal arm is modeled based on Hertz’s law, and a four-degree-of-freedom dynamic model of a vehicle shimmy system with consideration of clearance in the steering linkage mechanism is presented. Based on this model, numerical analysis is carried out, and the influences of the parameters, such as clearance, contact surface stiffness of the kinematic pair, wheel alignment parameters, and vehicle speed on the dynamic response of the vehicle shimmy system are discussed. It is shown that, considering the clearance in the steering linkage mechanism, these parameters can make a coupled contribution to the dynamic response of the vehicle shimmy system, and some effective measurements for vehicle shimmy attenuation are available. The conclusions will provide theoretical basis for effective vehicle shimmy control, especially for vehicles which are in use.
17 September 2020 in Vehicle System Dynamics
The dynamic model of the automobile shimmy system considering the sinusoidal road roughness excitation is established, and the response characteristic of the shimmy system is investigated with numerical simulations. Based on the complexification-averaging (CX-A) method, the slow flow equations of the shimmy system are obtained, and the shimmy angle of the front wheel is available on the basis of the analytical solution of the system. In addition, the bifurcation theory is applied to evaluate the stability of periodic solutions of the shimmy system exposed to the road roughness excitation. Finally, the laws of energy transfer between relevant subsystems of the shimmy system at various speeds are analysed. The suppression mechanism of the automobile shimmy by the damping of the steering system and the damping of the suspension at various speeds is also investigated. The conclusions provide theoretical supports for better anti-shimmy design, thereby improving the stability of the automobile.
21 November 2013 in Journal of Mechanical Science and Technology
1 February 2024 in IEEE Transactions on Vehicular Technology
The roll dynamic model of counterbalance forklift trucks that takes into account the hierarchical rolling process is proposed. The influence of vehicle speed on the critical instability characteristics is investigated under various steering angles using bifurcation theory. Then, a novel rollover index for forklift trucks is established utilizing dominant factors in both steering and traveling over obstacle scenarios. Subsequently, a hierarchical anti-rollover control scheme is formulated based on both the degree of instability and the output characteristics of the hydraulic actuator. In addition, an adaptive model predictive control (MPC) system is designed for adjusting the output force of the hydraulic cylinder and regulating the steering ratio. The simulation and experimental results indicate that the proposed comprehensive rollover index can continuously characterize the rolling state of the forklift truck when the wheels lift-off. Furthermore, the designed control framework yields superior performance for anti-rollover control under steering conditions.
19 April 2024 in IEEE Transactions on Intelligent Vehicles
Human-machine shared control has become a transitional solution from manual driving to autonomous driving, attracting increasing attention. In order to effectively enhance the stability of the vehicle and achieve adaptive collaborative control between the machine and human driver with different operating behaviors, this paper proposes a novel personalized steering behavior recognition method. On this basis, an adaptive authority allocation scheme is designed to alleviate the workload of the drivers and improve vehicle stability. Firstly, to identify different driving styles accurately, the K-means algorithm is modified based on the adaptive variation of weight coefficients. Subsequently, the numerical functions, considering tracking accuracy and steering error, are utilized to individually develop the reference models for various steering behaviors. Further optimal allocation problems involving driving workload, tracking performance, authority smoothness, and stability are addressed through MPC. Simulation results indicate that the proposed driver recognition method can distinguish ambiguous driving behaviors, and the shared steering control strategy demonstrates superior performance in path tracking, stability enhancing, and driver workload alleviating.