This study examines a planar dynamic model of a rotor-bearing-housing system incorporating a polyurethane support insert. The formulation takes into account the inertial, stiffness, and damping properties of the shaft, raceways, rolling elements, and cage, while the polyurethane layer is treated as an additional elastic–dissipative element. The equations of motion are derived using the Lagrangian formalism, based on kinetic, potential, and dissipation energies. Within the article, a frequency response analysis for different coating thicknesses is carried out, showing that the polyurethane insert reduces resonance frequencies by approximately 50-64 % while increasing vibration amplitudes by 67-146 %. A 2 mm layer provides a compromise between stiffness and damping, whereas thicker coatings (3-4 mm) enhance high-frequency vibration isolation but lead to higher sensitivity to low-frequency excitations. The novelty of this study lies in the introduction of a polyurethane elastic-dissipative layer into the planar dynamic model of the rotor-bearing-housing system. This approach enables an analytical representation of the polymer’s stiffness and damping effects and establishes a direct relationship between the polyurethane thickness and the system’s resonance behavior a topic not explicitly treated in previous works.
It is noted that the main factor in reducing the quality of the lint is its contamination caused by the increased content of crushed seeds. The latter is explained by the mechanical impact on the seed roller from the rigid elements of the working bodies of the linter machine, such as saws, grates and agitator. The magnitude of this impact largely depends on the density of the seed roller itself. In addition, its high density is the cause of additional energy costs for its rotation. To reduce the dynamic loads on the seeds in the roller, an original design of agitator with elastic inclined blades separated by elastic bushings is proposed. The proposed agitator provides intensive mixing of seeds in the seed roller both in the axial direction and in the direction of its rotation. It is shown that agitator with elastic blades allows to reduce energy costs by 20 % and reduce seed damage by 0.3 %
1 May 2022 in The American Journal of Agriculture and Biomedical Engineering
Treating seeds of leguminous crops against bruchuses 20 days before sowing with insecticide dressing agents at the rate of consumption of Avalanche 70% d. 4 heg / t and Cruiser Extra Cotton 362 c.t., 3 l /t at the end of the growing season preserves up to 45-50% yield.
В работе исследуется влияние усечённого конического эластомерного элемента, встроенного в подшипниковую опору, на вибрационное поведение роторной системы. Рассмотрена динамическая модель системы «ротор–подшипник–опора», учитывающая упругие и демпфирующие свойства эластомерного слоя и асимметрию центра масс ротора. На основе уравнений Лагранжа II рода получено уравнение вынужденных колебаний и выполнено численное моделирование амплитудно-частотных и переходных характеристик. Показано, что применение конического эластомера приводит к снижению резонансных амплитуд, смещению критической частоты и повышению динамической устойчивости системы.
Platinum group metals (PGMs) are key components of automotive emission-control catalysts, and spent automotive catalysts (SACs) are their main secondary source. This paper reviews hydrometallurgical, pyrometallurgical, magnetic-separation, biometallurgical, and ionic-liquid/deep-eutectic-solvent (IL/DES) routes and compares them for recovery, selectivity, energy demand, reagent hazard, technology readiness, and scalability, using values re-checked against accessible primary sources. Smelting with Cu- or Fe-based collectors is the only fully industrial route and gives the highest reported recoveries (≈90–99% for Pt and Pd and ≈85–98% for Rh). Hydrometallurgical leaching operates at lower temperature and separates the individual metals but relies on corrosive reagents and dissolves rhodium slowly. Magnetic-separation methods are pre-concentration steps, and biometallurgical and IL/DES routes remain at laboratory scale; their environmental performance has not yet been established by life-cycle assessment. A paired comparison of Rh with Pt and Pd shows that leaching at ≤90 °C typically extracts about 10–60 percentage points less Rh than the best-recovered companion metal, whereas gaps of about 10 points or less are reported for most smelting studies and for some intensified chloride leaching (≥150 °C, alkali calcination, or iron alloying). Integrated flowsheets coupling pretreatment with selective refining remain to be demonstrated at scale and need consistent techno-economic and life-cycle assessment.