4 December 2023 in Journal of Coatings Technology and Research
Poly(tetrafluoroethylene) (PTFE) is well known for its very low friction coefficient and thus widely used for antifriction applications, e.g., sliding lacquers, for many years. Because of the high wear rate and cold flow of the original polymer, PTFE is usually added in higher amounts to other polymer matrices as a lubricant. However, the incompatibility of PTFE requires lots of efforts to perform a homogeneous breaking down of agglomerates and particle distribution as well as dispersion stabilization of the physical mixtures during application and curing. PTFE can be functionalized by high energy irradiation and subsequently compatibilized with a polymer matrix by reactive extrusion resulting in chemical bonding of both polymers via suitable reactive groups. In this manner, poly(amide imide) (PAI) was coupled to γ-radiation modified PTFE micro-powder prior to the dispersion procedure. This study deals with the thermal and crystallization behavior of the PTFE lubricant in chemical bonded (cb) PAI-PTFEcb compound thin layers in comparison with those of the plain radiation modified PTFE depending on the cooling rate by DSC, Flash-DSC and WAXS. A morphological characterization of the extrudate as well as the coating gives information about the fragmentation and distribution of the PTFE phase in the PAI matrix. Furthermore, mechanical and surface properties of sliding lacquer films were analyzed after application on steel substrates by varying dry film thickness and curing. Graphical Abstract
2 December 2016 in Key Engineering Materials
Polytetrafluoroethylene (PTFE) powder is used as a solid lubricant in commercial antifriction coatings. However, most of the matrix polymers are usually not compatible with virgin PTFE resulting in low dispersion and mechanical film stability and adhesion. In our research PTFE TF 2025 was irradiated by g-beam generating PTFE micropowder with persistant radicals and functional groups. These functional groups are able to perform a chemical grafting (cg) of polyamideimide (PAI) and modified PTFE-micropowder by reactive extrusion in melt. Based on grinded extrudates PAI-PTFE-cg dispersions were formulated followed by characterizing dispersion as well as film properties. It was found, that PAI-PTFE-cg dispersion comprises very small PTFE-particles at higher g-irradiation doses in homogeneous dispersions. In addition, all samples showed outstanding film flexibility. Basic tribological properties under mixed lubrication were studied by using a ring-on-disk tribometer. Finally, diluted dispersions were applied to a multi-surface sliding bearing (four segments) for testing in a hydrodynamic plain test bench.
1 December 2008 in JOT Journal für Oberflächentechnik
6 January 2025 in Journal of Chemical Technology and Metallurgy
The current investigation reports the influence of siliconized slag powder on the mechanical properties of epoxy composites. At first, the received slag was crushed and milled followed by sieve analysis. The chemical composition of the slag waste of the steel-making process was inspected using X-ray fluorescence spectroscopy (XRF). Second, the treated slag was mixed with silicone rubber at high speed to produce siliconized slag. Then slag with and without silicon was incorporated into epoxy resin to produce epoxy composites, and mixing was done at the high-speed mixer. The mix was poured into Teflon-coated molds and allowed to harden for 3 days at room temperature. The mechanical performance of the prepared composites was inspected. Chemical functional groups and molecularstructure were analysed with attenuated total reflectance infrared spectroscopy (ATR-IR). The samples were examined with a Scanning electron microscope associated with energy-dispersive X-ray spectroscopy (SEM/EDX). Such a technique was used to obtain an idea of the fracture mode and the dispersion pattern of slag powder within the matrix and the chemical composition of the slag.
14 September 2023 in Journal of Tribology
In this article, solid lubricants are investigated to examine their tribological performance in a dry lubricated steel–bronze contact. The examined solid lubricants are made of polyamide (PA) and irradiated polytetrafluoroethylene (PTFE), which are chemically bonded by reactive melt extrusion. For the tribological investigations, a block-twin-disc test rig, on the one hand, and a three-disc test rig, on the other hand, were used under ambient conditions, where the solid lubricant for lubricating the steel–bronze contact was released from a block or a disc. Results from the tribological investigations are presented here, showing the friction and wear behavior in a steel–bronze contact depending on the slide-to-roll ratio in the contact between the steel disc and the compound body. Furthermore, surface analytical investigations on the steel and bronze discs were carried out. These studies showed that the chemical bonding of 20 wt% of irradiated PTFE in PA12 improves the wear and friction behavior in steel–bronze contact significantly, due to the buildup of a transfer film of PTFE on the steel surface.