Patrycja Walczuk-Gągała

Patrycja Walczuk-Gągała

Auto-generated profile, based on publicly available information

Patrycja Walczuk-Gągała

Lublin Univ Technol, Fac Mech Engn, Dept Met Forming, Ul Nadbystrzycka 36, PL-20618 Lublin, Poland

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2020 in Journal of Materials Processing Technology
Verified
Journal Article
Open access
Zbigniew PaterZbigniew Pater
Zbigniew Pater
JTJanusz Tomczak
Janusz Tomczak
TBTomasz Bulzak
Tomasz Bulzak
ŁWŁukasz Wójcik
Łukasz Wójcik
PWPatrycja Walczuk
Patrycja Walczuk

1 June 2018 in Advances in Science and Technology Research Journal
Verified
Journal Article
Open access
Zbigniew PaterZbigniew Pater
Zbigniew Pater
PWPatrycja Walczuk
Patrycja Walczuk
KLKonrad Lis
Konrad Lis
ŁWŁukasz Wójcik
Łukasz Wójcik
The paper addresses the problem of material fracture in cross rolling processes. A new test based on rotary compression for determining limit values of the damage function after the Cockroft-Latham criterion is proposed. A FEM analysis is performed to determine the stress and strain states in a...

1 March 2019 in Advances in Science and Technology Research Journal
Verified
Journal Article
Open access
Zbigniew PaterZbigniew Pater
Zbigniew Pater
ŁWŁukasz Wójcik
Łukasz Wójcik
PWPatrycja Walczuk
Patrycja Walczuk
The article presents a comparison of the piercing process conducted in a two-roll Diescher mill and a three-roll mill. The comparative analysis was based on the numerical simulations of the aforementioned processes, obtained using Forge NxT 1.1. software. It was stated that the most favourable...

6 February 2020 in Materials
Verified
Journal Article
Open access
PDF file
Zbigniew PaterZbigniew Pater
Zbigniew Pater
Janusz TomczakJanusz Tomczak
Janusz Tomczak
TBTomasz Bulzak
Tomasz Bulzak
ŁWŁukasz Wójcik
Łukasz Wójcik
PWPatrycja Walczuk-Gągała
Patrycja Walczuk-Gągała
The subject-matter of the article is the ductile fracture of materials—A phenomenon occurring in numerous metal forming processes. In order to prognosticate the possibility of a fracture, damage criteria are employed. Their effectiveness, however, depends on the accurate determination of the critical values of damage. These values are obtained through calibrating tests, where the stress state has to be as similar to the actual process as possible. The currently employed calibrating tests do not enable one to determine the limit values of the damage function when the Mannesmann effect occurs. Therefore it was not possible to effectively prognosticate the material fracture in the processes of cross- and skew-rolling. A new calibrating test, based on rotational compression of a cylindrical sample, in which the fractures are caused by the Mannesmann effect, was developed at the Lublin University of Technology. This test was discussed in the article, with a particular focus on the stress and strain state in the sample. A practical use of the test was presented on the example of C45 grade steel, formed in the temperature equal 1150 °C. In the research ten material damage criteria were adopted.

1 September 2021 in Advances in Science and Technology Research Journal
Verified
Journal Article
Open access
Zbigniew PaterZbigniew Pater
Zbigniew Pater
PWPatrycja Walczuk-Gągała
Patrycja Walczuk-Gągała
The article presents a conception of manufacturing a hollow axle using three skewed rolls moving at the same rotating speed, axially moving chuck and a moving mandrel. The outer shape of the axle is obtained as a result of combining the radial feed of the rolls with axial feed of the chuck. The...

1 March 2020 in Advances in Science and Technology Research Journal
Verified
Journal Article
Open access
Zbigniew PaterZbigniew Pater
Zbigniew Pater
KLKonrad Lis
Konrad Lis
PWPatrycja Walczuk-Gągała
Patrycja Walczuk-Gągała
The article presents an innovative method of manufacturing hollow rail axles using three combined wedge rolls. The proposed solution was evaluated using numerical simulation. Two cases of forming, differing in the wall thickness of the billet, were analysed. The geometry of the formed axles, distributions of the effective strain, temperature and damage function were presented. Moreover, the changes to the forces and torques acting on each roll were presented.