This study presents a method of producing thick (i.e., in the range) polycrystalline free-standing flexible films. Preparation is carried out by sputtering on silicon conventional substrates using tantalum as a buffer and capping layer. Magnetic and magnetocaloric properties show good agreement with data from high-purity bulk , and are not altered by substrate removal. Moreover, the free-standing film is flexible and all the relevant magnetic properties (i.e., Curie temperature , saturation magnetization , and isothermal entropy change ) are preserved under bending (up to a strain over the two film sides). The technological opportunities heralded by availability of magnetocaloric flexible self-sustaining films are discussed in the conclusions with particular focus on energy-conversion applications (i.e., cooling and thermal energy harvesting). More precisely, the output-power upper bound of an thermal-energy harvester deploying a flexible film with the reported properties is worked-out using a thermal switch model presented elsewhere. The calculations show a potential output able to supply the new generation of IoT wireless devices as well as small medical implants. The result moot free-standing flexible films as a benchmark for a new generation of small high-throughput magnetocaloric energy-conversion devices.
Magnetization, Curie temperature and isothermal entropy change have been measured in Gadolinium 3 μm thick films. We present the comparison between the structural and magnetic properties of samples deposited either at room temperature or at 550°C onto silicon substrate (100) with a thermally oxidized layer. The results are discussed using as a reference, data from bulk Gd single crystals. As compared to bulk values, the room temperature grown film shows lower Curie temperature ( ∼ 280 K) and weaker entropy change ( ∼ 6.8 Jkg−1K−1) under application of magnetic field ramp from 0 to 5 Tesla. On the contrary the 550○C deposited film shows a Curie temperature ( ∼ 293 K) and a maximum isothermal entropy change ( ∼ 8.9 Jkg−1K−1) both in good agreement with values expected for bulk samples. The behavior of the room temperature deposited samples are briefly discussed and compared with similar effects observed in bulk samples with different degree of purity and homogeneity.
The use of magnetocaloric material in microelectromechanical energy conversion devices requires freestanding films with smooth surfaces to allow fast and efficient heat transfer. We present and discuss a mechanical method to produce freestanding thick Gadolinium films showing excellent magnetic properties, and high-quality surfaces on both sides. Polycrystalline Gd films have been prepared by sputtering on a silicon substrate with a thermally oxidized layer with different thicknesses. Films have been grown at 543 K. Tantalum and Tungsten have been used as buffer layers because of their corrosion resistance and of their thermal conductivity. The magnetic and surface properties of the freestanding films are presented, with special focus on the role of using different capping layers. Full characterizations of the three freestanding Gd films, including AFM measured surface roughness, XRD patterns, Curie temperature, thermo-magnetic curves, and maximum entropy change, are presented and discussed.
Thermomagnetic generators (TMG) are promising devices for converting low‐grade waste heat into electricity. Self‐actuation using permanent magnets is the key to autonomy. Tailoring thermomagnetic materials in the form of flexible and freestanding films is a way toward high power‐density through fast, and efficient heat transfer. Design optimization, and the use of micromagnets represent a unique opportunity toward miniaturization. Here, the operation and performance of a TMG using a flexible freestanding Gd film as the active substance, and an array of NdFeB micromagnets as field source is presented. The Gd film self oscillates under the effect of the magnetic field gradient, entering in contact with the heat source, and the heat sink alternatively. At an operating frequency of Hz, a designed piezoelectric spring converts the mechanical oscillation into electrical energy, reaching up to power‐output with temperature difference. The magnetic field gradient acting over the thermal switch, and triggering the caloric response of this thick Gd film, is generated by an array of thick NdFeB micromagnets, which produces a T variation in field strength over a gap. The power density normalized to the combined volume of the Gd film and of the magnet reaches up to .