28 April 2017 in Physics of Plasmas
We report on the most recent and successful effort at controlling the trajectory and symmetry of a high density carbon implosion at the National Ignition Facility. We use a low gasfill (0.3 mg/cc He) bare depleted uranium hohlraum with around 1 MJ of laser energy to drive a 3-shock-ignition relevant implosion. We assess drive performance and we demonstrate symmetry control at convergence 1, 3–5, 12, and 27 to better than ±5 μm using a succession of experimental platforms. The symmetry control was maintained at a peak fuel velocity of 380 km/s. Overall, implosion symmetry measurements are consistent with the pole-equator symmetry of the X-ray drive on the capsule being better than 5% in the foot of the drive (when shocks are launched) and better than 1% during peak drive (main acceleration phase). This level of residual asymmetry should have little impact on implosion performance.
4 February 2010 in Physical Review Letters
The viability of fast-ignition (FI) inertial confinement fusion hinges on the efficient transfer of laser energy to the compressed fuel via multi-MeV electrons. Preformed plasma due to the laser prepulse strongly influences ultraintense laser plasma interactions and hot electron generation in the hollow cone of an FI target. We induced a prepulse and consequent preplasma in copper cone targets and measured the energy deposition zone of the main pulse by imaging the emitted radiation. Simulation of the radiation hydrodynamics of the preplasma and particle in cell modeling of the main pulse interaction agree well with the measured deposition zones and provide an insight into the energy deposition mechanism and electron distribution. It was demonstrated that a under these conditions a 100 mJ prepulse eliminates the forward going component of electrons.
1 March 2020 in Physics of Plasmas
The micrometer-scale tube that fills capsules with thermonuclear fuel in inertial confinement fusion experiments at the National Ignition Facility is also one of the implosion's main degradation sources. It seeds a perturbation that injects the ablator material into the center, radiating away some of the hot-spot energy. This paper discusses how the perturbation arises in experiments using high-density carbon ablators and how the ablator mix interacts once it enters the hot-spot. Both modeling and experiments show an in-flight areal-density perturbation and localized x-ray emission at stagnation from the fill-tube. Simulations suggest that the fill-tube is degrading an otherwise 1D implosion by ∼2×, but when other degradation sources are present, the yield reduction is closer to 20%. Characteristics of the fill-tube assembly, such as the through-hole size and the glue mass, alter the dynamics and magnitude of the degradation. These aspects point the way toward improvements in the design, some of which (smaller diameter fill-tube) have already shown improvements.
28 February 2017 in Physics of Plasmas
The thin membrane that holds the capsule in-place in the hohlraum is recognized as one of the most significant contributors to reduced performance in indirect drive inertial confinement fusion (ICF) experiments on the National Ignition Facility. This membrane, known as the “tent,” seeds a perturbation that is amplified by Rayleigh-Taylor and can rupture the capsule. A less damaging capsule support mechanism is under development. Possible alternatives include the micron-scale rods spanning the hohlraum width and supporting either the capsule or stiffening the fill-tube, a larger fill-tube to both fill and support the capsule, or a low-density foam layer that protects the capsule from the tent impact. Experiments are testing these support features to measure their imprint on the capsule. These experiments are revealing unexpected aspects about perturbation development in indirect drive ICF, such as the importance of shadows coming from bright spots in the hohlraum. Two dimensional and 3D models are used to explain these features and assess the impact on implosion performance. Experiments and modeling suggest that the fill-tube supported by a perpendicular rod can mount the capsule without any additional perturbation beyond that of the fill tube.
1 May 2020 in Physics of Plasmas
We describe the overall performance of the major indirect-drive inertial confinement fusion campaigns executed at the National Ignition Facility. With respect to the proximity to ignition, we can describe the performance of current experiments both in terms of no-burn ignition metrics (metrics based on the hydrodynamic performance of targets in the absence of alpha-particle heating) and in terms of the thermodynamic properties of the hotspot and dense fuel at stagnation—in particular, the hotspot pressure, temperature, and areal density. We describe a simple 1D isobaric model to derive these quantities from experimental observables and examine where current experiments lie with respect to the conditions required for ignition.
1 September 2017 in Physics of Plasmas
By the time an inertially confined fusion (ICF) implosion has converged a factor of 20, its surface area has shrunk , making it an inefficient x-ray energy absorber. So, ICF implosions are traditionally designed to have the laser drive shut off at a time, toff, well before bang-time, tBT, for a coast-time of ns. High-foot implosions on NIF showed a strong dependence of many key ICF performance quantities on reduced coast-time (by extending the duration of laser power after the peak power is first reached), most notably stagnation pressure and fusion yield. Herein we show that the ablation pressure, pabl, which drives high-foot implosions, is essentially triangular in temporal shape, and that reducing tcoast boosts pabl by as much as prior to stagnation thus increasing fuel and hot-spot compression and implosion speed. One-dimensional simulations are used to track hydrodynamic characteristics for implosions with various coast-times and various assumed rates of hohlraum cooling after toff to illustrate how the late-time conditions exterior to the implosion can impact the fusion performance. A simple rocket model-like analytic theory demonstrates that reducing coast-time can lead to a % higher implosion velocity because the reduction in x-ray absorption efficiency at late-time is somewhat compensated by small ( %) ablator mass remaining. Together with the increased ablation pressure, the additional implosion speed for short coast-time implosions can boost the stagnation pressure by as compared to a longer coast-time version of the same implosion. Four key dimensionless parameters are identified and we find that reducing coast-time to as little as 500 ps still provides some benefit. Finally, we show how the high-foot implosion data is consistent with the above mentioned picture.