Dragan Petrović

Dragan Petrović

Auto-generated profile, based on publicly available information

Dragan Petrović

University of Kragujevac, Faculty of Mechanical and Civil Engineering in Kraljevo, Dositejeva 19, 36000 Kraljevo, Serbia

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2012 in Engineering Failure Analysis
Verified
Journal Article
Closed access
MSMile Savković
Mile Savković
MGMilomir Gašić
Milomir Gašić
DPDragan Petrović
Dragan Petrović
NZNebojša Zdravković
Nebojša Zdravković
RPRadmila Pljakić
Radmila Pljakić

19 June 2017 in Measurement Science and Technology
Verified
Journal Article
Closed access
PDF file
MBMilan B Bižić
Milan B Bižić
DPDragan Z Petrović
Dragan Z Petrović
MTMiloš C Tomić
Miloš C Tomić
ZDZoran Djinovic
Zoran Djinovic
This paper presents the development of a unique method for experimental determination of wheel–rail contact forces and contact point position by using the instrumented wheelset (IWS). Solutions of key problems in the development of IWS are proposed, such as the determination of optimal locations, layout, number and way of connecting strain gauges as well as the development of an inverse identification algorithm (IIA). The base for the solution of these problems is the wheel model and results of FEM calculations, while IIA is based on the method of blind source separation using independent component analysis. In the first phase, the developed method was tested on a wheel model and a high accuracy was obtained (deviations of parameters obtained with IIA and really applied parameters in the model are less than 2%). In the second phase, experimental tests on the real object or IWS were carried out. The signal-to-noise ratio was identified as the main influential parameter on the measurement accuracy. Тhе obtained results have shown that the developed method enables measurement of vertical and lateral wheel–rail contact forces Q and Y and their ratio Y / Q with estimated errors of less than 10%, while the estimated measurement error of contact point position is less than 15%. At flange contact and higher values of ratio Y / Q or Y force, the measurement errors are reduced, which is extremely important for the reliability and quality of experimental tests of safety against derailment of railway vehicles according to the standards UIC 518 and EN 14363. The obtained results have shown that the proposed method can be successfully applied in solving the problem of high accuracy measurement of wheel–rail contact forces and contact point position using IWS.

1 July 2012 in Engineering Structures
Verified
Journal Article
Closed access
MDMirko Djelosevic
Mirko Djelosevic
VGVladeta Gajic
Vladeta Gajic
DPDragan Petrovic
Dragan Petrovic
MBMilan Bizic
Milan Bizic

20 June 2023 in Metrology and Measurement Systems
Verified
Journal Article
Open access
PDF file
MBMilan Bižić
Milan Bižić
DPDragan Petrović
Dragan Petrović
The paper presents the design of a specific type of instrumented wheelset intended for continuous measuring of lateral and vertical wheel-rail interaction forces 𝑌 and 𝑄, in accordance with regulations EN 14363 and UIC 518. The platform is a standard heavy wheelset BA314 with an axle-load of 25 tons. The key problems of smart instrumentalization are solved by the use of the wheel's numerical FEM model, which provides a significant cost reduction in the initial stage of development of the instrumented wheelset. The main goal is to ensure high measuring accuracy. The results of the FEM calculations in ANSYS are basis for identification of the distribution of strains on the internal and external side of the wheel disc. Consequently, the most convenient radial distances for installation of strain gauges of Wheatstone measuring bridges are determined. In the next stage, the disposition, number and ways of interconnection of strain gauges in the measuring bridges are defined. Ultimately, an algorithm for inverse determination of parameters 𝑌 and 𝑄 based on mixed signals from the measuring bridges is developed. The developed solution is validated through tests on specific examples, using a created numerical FEM model. A high accuracy of estimation of unknown parameters 𝑌 and 𝑄 is obtained with an error of less than 4.5%, while the error of estimation of their ratio 𝑌 /𝑄 is less than 2%. Therefore, the proposed solution can be efficiently used in the instrumentalization of the considered wheelset, while the problems of its practical implementation will be the subject of further research.

18 August 2012 in Engineering with Computers
Verified
Journal Article
Closed access
PDF file
MBMilan Bižić
Milan Bižić
RBRadovan R. Bulatovic
Radovan R. Bulatovic
DPDragan Petrović
Dragan Petrović
MGMilomir Gašić
Milomir Gašić
MSMile Savković
Mile Savković

1 October 2012 in Engineering Failure Analysis
Verified
Journal Article
Closed access
DPDragan Z. Petrović
Dragan Z. Petrović
MBMilan B. Bižić
Milan B. Bižić