27 June 2016 in Journal of Hydraulic Research
Wall deflection in supercritical flow induces standing waves which significantly influence the flow field close to the wall. This paper analyses the flow in the converging stepped spillway, using two scale-models with different step heights and convergence angles. Results show that the height and the width of the standing wave increase with the increase of the convergence angle. Air concentration decreases while the air–water mixture velocity and residual energy head increase in the vicinity of the converging wall and gradually attain the values for the undisturbed flow outside the standing wave. Compared to the prismatic chutes of equal upstream width, converging spillways are less efficient energy dissipators. Equations for predicting the maximum flow depth and the width-averaged residual energy are proposed.
12 September 2014 in Journal of Hydraulic Research
A complex flow pattern occurring in a circular conduit bend with supercritical flow has been studied. The main objective was to obtain reliable criteria for prediction of the onset of helical and choking flow, in order to facilitate the design of bottom outlets, tunnel spillways and drainage collectors with bends. A series of scale model experiments provided data for developing empirical relationships describing the effects of the bend curvature, bend deflection angle and approach flow conditions (relative flow depth and Froude number) on the inception of helical and choking flow. Expressions for the energy bend loss coefficient were also proposed. The bend curvature and approach flow conditions proved to have a major influence on the onset of helical flow, while the deflection angle becomes an important parameter for angles less than 45°. Bend curvature and deflection angle have commensurable influence on the onset of choking flow.
1 May 2014 in Proceedings of the Institution of Civil Engineers - Water Management
This study considers the hydraulic design of a shaft spillway with a constriction at the upstream end of the vertical bend. The effect of key factors relating to the capacity of the crest, shaft and tunnel is assessed using hydraulic model investigations of several spillways and available experience from other relevant research. As a result, new expressions for the discharge and velocity coefficients have been established. An algorithm for the design procedure, based on previous experience, is also presented.
10 July 2020 in Measurement Science and Technology
High-frequency oscillations and high surface aeration, induced by strong turbulence, make water depth measurement for hydraulic jumps a persistently challenging task. The investigation of hydraulic jump behaviour continues to be an important research theme, particularly with regards to the stilling basin design. Reliable knowledge of time-averaged and extreme values along a depth profile can help develop an adequate design of a stilling basin, improve safety, and aid the understanding of the jump phenomenon. This paper presents an attempt to mitigate certain limitations of existing depth measurement methods by adopting a non-intrusive computer vision-based approach to measuring the water depth profile of a hydraulic jump. The proposed method analyses video data in order to detect the boundary between the air–water mixture and the laboratory flume wall. This is achieved by coupling two computer vision methods: (1) analysis of the vertical image gradients, and (2) general-purpose edge detection using a deep neural network model. While the gradient analysis technique alone can provide adequate results, its performance can be significantly improved in combination with a neural network model which incorporates a ‘human-like’ vision within the algorithm. The model coupling reduces the likelihood of false detections and improves the overall detection accuracy. The proposed method is tested in two experiments with different degrees of jump aeration. Results show that the coupled model can reliably and accurately capture the instantaneous depth profile along the jump, with low sensitivity to image noise and flow aeration. The coupled model presented fewer false detections than the gradient-based model, and offered consistent performance in regions of high as well as low aeration. The proposed approach allows for automated detection of the free-surface interface and expands the potential of computer vision-based measurement methods in hydraulics.
1 January 2014 in FME Transactions
In this paper a complex flow pattern occurring in a closed conduit bend with supercritical flow is analyzed. The research was done by a scale (physical hydraulic) model, and a numerical model developed in Ansys (Fluent) program surrounding. This article compares the results obtained by numerical and physical (scale) models, providing comments and recommendations for their application. Based on these results, simple empirical relationships were developed, describing the effects of the bend deflection angle and approach flow conditions (non dimensional depth and the Froude number upstream from the bend) on the considered flow.
1 April 2017 in Journal of Hydrodynamics