We present high‐resolution 3D images of the crustal S‐wave velocity structure beneath northeastern Tibet, via ambient noise imaging techniques. The data come from continuous recordings taken in one year by a seismic array consisting of 366 broadband stations in the study region. The results show a substantial and pervasive middle crust low‐velocity structure (<3.4 km/s) beneath the plateau region, which partially protrudes northeastward across the West Qinling fault, reflecting channel flow from inside the plateau and material extrusion in the periphery. The growth of the northeastern Tibetan Plateau in the study region is manifested in its northeastward expansion and thickening driven by crustal channel flow, accompanied with upper crust shortening.
19 September 2018 in Journal of Geophysical Research: Solid Earth
Using seismic data recorded by a dense temporary seismic array, we apply a waveform matched‐filter technique and obtain an early aftershock catalog around the mainshock rupture zone of the 2008 Wenchuan, Sichuan, China, earthquake. Specifically, we use 1,273 events in a relocated aftershock catalog as templates and scan through the waveforms within 7 days following the mainshock. We obtain up to ∼5.3 and ∼10 times more aftershocks than the standard and relocated catalogs, respectively. We find that early aftershocks mostly occurred below 10 km depth, downdip to large coseismic slip areas. Early aftershocks also show minor along‐strike migration with time since the mainshock, indicating triggering of afterslip following the mainshock. From the epicentral region to Beichuan where the mainshock slip was primarily reverse faulting, early aftershocks illustrated the Yingxiu‐Beichuan and Guanxian‐Jiangyou faults as high‐angle listric feature and rooted to a gentle dipping plane at the depth of ∼20 km. The aftershocks in the northeast segment of the Longmen Shan faults mostly occurred along a near‐vertical dipping fault, consistent with the primary strike‐slip component of mainshock slip in this region. In addition, differences in early and long‐term aftershock distribution indicate significant postseismic deformation along the conjugate Xiaoyudong fault. Our results help to illuminate the deep geometry of the Longmen Shan fault zone and the early evolution after the Wenchuan mainshock, which provides additional constraints to the mechanism of plateau uplifting.
27 May 2025 in Journal of Geophysical Research: Solid Earth
The 2024 Mw 7.0 Wushi earthquake is the largest earthquake within the seismically active Tian Shan during the past three decades. Through integrated analyses of seismic, geodetic, and geologic data, here we investigate the fault structure corresponding to the Wushi mainshock and subsequent aftershocks. Our work reveals (i) a moderately-dipping, oblique-reverse main-fault rupture and (ii) numerous steeply to vertically-dipping subfault ruptures that align obliquely in cross-section to the main fault. The subfaults made clear aftershock concentrations while the main fault did not, and a shallowly-buried subfault generated clear surface rupture despite the main fault being totally blind. This fault network, misoriented with the prevailing background stress field, likely forms through a reactivation of inherited planes of weakness. These results demonstrate the significant control of structural inheritance on fault geometric architecture and highlight the complexity of seismic activity and rupture behavior of the yielding fault network.
On 17 November 2017, a Mw 6.5 earthquake occurred in Mainling County, Nyingchi City, China. The epicenter was located in the Namche Barwa region of the eastern Himalayan syntaxis. Here, we have derived coseismic deformation from Global Positioning System (GPS) data and ascending Sentinel-1A Synthetic Aperture Radar (SAR) data. Based on a joint inversion of the two datasets, we obtained the coseismic slip distribution along a curved, northeast trending, and high-angle (dip angle of 75°) thrust fault. Our results show that the seismic moment release was 7.49 × 1018 N∙m, corresponding to a moment magnitude of Mw 6.55. The maximum slip was 1.03 m and the main rupture zone extended to a 12 km depth. The earthquake may have been related to the release of strain accumulated during the subduction of the Indian plate beneath the Eurasian continent. We identified a high strain rate and low b-values around the epicentral area before the earthquake, indicating that the earthquake was nucleated under a high strain/stress state. The data indicate two regions, southwest and southeast to the epicenter (the eastern Main Himalaya Thrust and northern end of the Sagaing fault), which remain under high stress/strain conditions and pose a significant seismic hazard.
The 22 January 2024 Mw 7.0 Wushi earthquake (WSEQ) struck the Wushi Basin along the southern margin of the Tian Shan, Xinjiang, China. As the largest earthquake in the region since the 1992 Mw 7.3 Suusamyr earthquake (Kyrgyzstan), the WSEQ is among the few large earthquakes captured by high-quality observational datasets—including the earthquake early warning network operated by China Earthquake Administration before and a dense temporary seismic array deployed immediately after the mainshock in the Tian Shan region. This provides a rare opportunity to investigate fault network activation and rupture behavior in the tectonically active southern Tian Shan.We picked and associated Pg/Sg phases using a neural network and the REAL method, respectively, followed by relocating all events via NonLinLoc and the double-difference relocation method. Focal mechanisms were also determined for aftershocks with M ≥4.Our results are as follows: 1) The seismogenic fault of the WSEQ strikes northwest, correponding to a moderately-dipping, oblique-reverse main-fault rupture; 2) The mainshock triggered reactivation of a series of small-scale faults, and aftershock distribution is closely linked to these active faults in the study area; 3) Aftershocks are concentrated on subfaults rather than the main fault; and a shallowly buried subfault produced distinct surface rupture whereas the main fault is completely blind. This fault network, misaligned with the prevailing background stress field, likely forms through a reactivation of inherited weak planes.These results illustrate that structural inheritance strongly controls fault geometric architecture and underscores the complexity of seismic activity and rupture behavior within the active fault network.