New modulation codes are presented for a random modulation cw lidar. One characteristic of these modulation codes is that for very noisy background conditions, the signal-to-noise ratio is improved by using these new sequences, and is better than for the maximum-length sequence (the M-sequence) which is commonly used as the modulation code. Another characteristic of these modulation codes is that there is no correlation between them. This fact will be useful for the simultaneous multitransmitter of the differential absorption lidar. These two characteristics of the new modulation codes were confirmed experimentally.
A study on the feasibility of using pseudorandom modulation continuous-wave (PMCW) Na lidar for mesopause-region temperature and horizontal wind measurements is presented with a number of specific geometries and associated beam-telescope overlap functions, suitable for ground-based and airborne deployments. The performance of these deployment scenarios is analyzed by scaling from the received signal and sky background and the measurement uncertainties in temperature and horizontal wind of the well-tested Colorado State University pulsed Na lidar. Using currently available high-power () continuous-wave Na narrowband lasers, a compact PMCW bistatic Na lidar system can indeed be deployed to simultaneously measure mesopause-region temperature and horizontal winds on a continuous basis, weather permitting.
A 1.6 μm differential absorption Lidar (DIAL) system for measurement of vertical CO2 mixing ratio profiles has been developed. A comparison of CO2 vertical profiles measured by the DIAL system and an aircraft in situ sensor in January 2014 over the National Institute for Environmental Studies (NIES) in Tsukuba, Japan, is presented. The DIAL measurement was obtained at an altitude range of between 1.56 and 3.60 km with a vertical resolution of 236 m (below 3 km) and 590 m (above 3 km) at an average error of 1.93 ppm. An in situ sensor for cavity ring-down spectroscopy of CO2 was installed in an aircraft. CO2 mixing ratio measured by DIAL and the aircraft sensor ranged from 398.73 to 401.36 ppm and from 399.08 to 401.83 ppm, respectively, with an average difference of −0.94 ± 1.91 ppm below 3 km and −0.70 ± 1.98 ppm above 3 km between the two measurements.
18 June 2019 in Journal of Geophysical Research: Space Physics
A frequency‐tunable resonance scattering lidar with high temporal/vertical resolutions (1 min/15 m) observed sporadic calcium ion (Ca+s) layers at ~100 km over Tachikawa (geographical/geomagnetic latitude: 35.7°N/27.1°N), Japan, on 21–22 August 2014. Simultaneously, sporadic E (Es) parameters and medium‐scale traveling ionospheric disturbances (MSTIDs) were observed by an ionosonde and Global Navigation Satellite System receiver network, GEONET, respectively. The maximum densities of the Ca+ and electrons in the Es layer had a strong positive correlation. As observation started ~23:30 LT, the Ca+s layer and the associated Es layer descended at ~2.8 km/hr with density irregularities including Kelvin‐Helmholtz billow‐like structures suggesting the presence of background neutral wind shear and instability. And the total electron content variations showed large amplitude associated with the MSTIDs at an altitude of 300 km in synchronization with the Ca+ column abundance surges at 100 km over Tachikawa; in their respective E and F region locations connected by geomagnetic field line these irregularities are found to vary in phase. At ~02:00 LT, the Ca+s layer stopped descending at ~100 km due to larger ion‐neutral collision frequency in the lower altitudes and resided there quietly until sunrise; both Ca+ column abundance enhancements and the large total electron content variation disappeared as the descent of the Ca+s layer stopped, implicating that the MSTID structure cannot be sustained without the density irregularities of the Es layer. This is the first synchronous observation of the coupling between the Es density irregularities and the MSTIDs in the F region along a common magnetic flux tube.
21 December 2009 in Japanese Journal of Applied Physics
Inverse techniques using atmospheric transport models are developed to estimate the CO2 sources and sinks based on the observed data. In comparison with the ground-based monitoring network, CO2 measurements for vertical profiles in the troposphere have been due to the limited observations by using campaign-style aircrafts and the commercial airlines with limited spatial and temporal coverage. The differential absorption lidar (DIAL) with the range resolution is expected to bring several advantages over passive measurements, for example, daytime coverage and neglecting influences of aerosol and cirrus layers. We have succeeded to develop the 1.6 μm DIAL technique using direct detection method for measurement of CO2 concentration profiles in the atmosphere. This paper describes the advanced CO2 1.6 μm DIAL technique consisting of the optical parametric generator (OPG) transmitter (10mJ/pulse) that excited by the LD pumped Nd:YAG laser with high repetition rate (500Hz) and the receiving optics that included the large telescope with 60cm diameter and the photomultiplier tube with high quantum efficiency (~8%) operating at the photon counting mode and the narrowband interference filter (0.5nm bandwidth) for daytime observations. The CO2 concentration profiles from ground to an altitude of 12km are conducted to measure with better than 1% standard deviation using 500m bins by this CO2 DIAL.