17 November 2021 in Scientific Reports
Fused silica with structured and continuous patterns is increasingly demanded in advanced imaging and illumination fields because of its excellent properties and functional performance. Atmospheric pressure plasma, based on pure chemical etching under atmospheric pressure, is developed as a promising fabrication technique for fused silica due to its deterministic high material removal rate, controllable removal imprint and no mechanical load. The stable and controllable Gaussian-shape removal function makes computer-controlled plasma tool potential to generate complex structures with high accuracy, efficiency and flexibility. In the paper, computer-controlled atmospheric pressure plasma structuring (APPS) is proposed to fabricate 2D/3D patterns on fused silica optics. The capacitively coupled APPS system with a double-layer plasma torch and its discharge characteristics are firstly developed. By means of multi-physics simulation and process investigation, the stable and controllable Gaussian-shape removal function can be achieved. Two different structuring modes, including discrete and continuous APPS, are explored for 2D/3D patterns. A series of structuring experiments show that different kinds of 2D patterns (including square lens array, hexagon lens array and groove array) as well as complex 3D phase plate patterns have been successfully fabricated, which validates the effectiveness of the proposed APPS of 2D/3D patterns on fused silica optics.
19 February 2025 in Optics Express
Large-aperture continuous phase plate (CPP) plays a crucial role in high-power laser systems, spawning a substantial demand for high-volume manufacturing. Given the intricate surface topographies of CPPs, the utilization of multiple tool influence functions (TIFs) during fabrication has been widely recognized as an efficacious means to strike a more favorable balance between machining efficiency and precision. However, it should be noted that even with the same set of multiple TIFs, the collaborative performance can exhibit variations across different designed CPP surfaces, thereby introducing ambiguity into the determination of the optimal processing strategy. In this manuscript, we introduce an optimized planning paradigm underpinned by multiple collaborative processing (MCP) analysis, which is specifically applied to the atmospheric pressure plasma processing (APPP) technique for CPP imprinting. Initially, the fundamental characteristics of APPP are expounded, succeeded by the elucidation of the MCP analysis concept and its corresponding simulation demonstrations. Subsequently, the factors influencing the collaborative performance are dissected through the transformation of the multi-objective optimization problem (MOP), trailed by meticulous simulations. Moreover, an advanced optimal planning methodology is devised to identify the optimal processing scheme from the existing TIF library for any arbitrarily designed CPP surface. Eventually, a comprehensive suite of simulations and experiments is carried out to validate the proposed optimal planning approach. The experimental outcomes affirm that the proposed method not only enables the identification of an optimal processing scheme in a feasible and effective manner but also substantially curtails the computational overhead, thereby augmenting the overall efficiency of CPP fabrication via APPP.
19 December 2025 in Optics Express
In optical fabrication, millimeter-scale errors, particularly from 1 mm to 10 mm, can be effectively corrected using spot-sized ion beam figuring (IBF), which enables the tool influence function (TIF) size to be reduced to the millimeter or submillimeter level. However, when the error scale approaches the TIF size, the precision of dwell time calculation is limited, necessitating the increased additional material removal (AMR) to achieve accurate correction, at the cost of extended machining times. To address this trade-off, this study proposes the frequency-adaptive dwell time optimization method that leverages linear time-invariant (LTI) systems and transfer functions (TF) to pre-compensate material removal, enhancing both precision and efficiency. The comprehensive simulations demonstrate its distinctive advantages over traditional AMR optimization, particularly when higher-spatial-frequency errors predominate. In experimental validation, the shell-type structure was used to generate errors with spatial wavelengths from 2.6 mm to 11.2 mm. After correction using the TIF with the full width at half maximum (FWHM) of 2 mm, the root-mean-square (RMS) value of error was successfully reduced from 5.68 nm to 0.73 nm, confirming its feasibility and effectiveness.
15 May 2025 in Optics Express
With the continuous advancement of technology, the manufacturing standards for optical components have become increasingly stringent. Due to variations in material properties, achieving satisfactory surface roughness on certain materials remains challenging. Researchers have employed surface modification techniques to alter the properties of substrate surfaces, resulting in enhanced polishing precision on modification layers. However, subsequent investigations have revealed that during the precise figuring of these ultra-smooth, damage-free modification layers, a significant number of defect structures emerge on the surface, leading to a marked increase in surface roughness and severely limiting ultimate machining precision. To address these issues, this study focuses on ion beam figuring (IBF) as a case study. It first elucidates the mechanisms of material removal from the modification layer surface during IBF through microscopic characterization techniques and molecular dynamics (MD) simulations. Microscopic analysis indicates that the morphology of the substrate significantly influences the properties of the modification layer. The MD simulation results demonstrate that variations in the properties of the modification layer contribute to discrepancies in local sputtering yields, which in turn lead to the formation of surface defects. Finally, based on these findings, a method for achieving ultra-smooth, damage-free fabrication of modification layer surfaces is proposed, and its feasibility is experimentally validated. The results demonstrate that modification layers grown on smooth, defect-free substrates exhibit superior quality, with surface roughness remaining below 0.2 nm RMS after figuring, while maintaining an ultra-smooth and damage-free state.