Chao Peng

Chao Peng

Auto-generated profile, based on publicly available information

Chao Peng

School of Architecture & Civil Engineering, Liaocheng University, Liaocheng, Shandong 252059, China

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2021 in Advances in Civil Engineering
Verified
Journal Article
Open access
PDF file
CPChao Peng
Chao Peng
WLWanrong Liu
Wanrong Liu
Rock burst is one of the disaster accidents that can easily happen in rock cavern engineering. At present, one of the most commonly used methods to control rock burst is borehole pressure relief technology. In this paper, the influence of drilling layout schemes on the pressure relief effect of surrounding rock mass is systematically studied. The research results show that the strength reduction degree, AE evolution characteristics, failure modes of rock samples with different borehole positions, boreholes spacing, boreholes dip angles, and boreholes layout forms are different. The strength reduction degree of rock sample with an inclined arrangement form is the largest, followed by the arrangement form being up three‐flower layout or down three‐flower layout. Using the inclined layout and three‐flower layout can achieve better pressure relief effect of the surrounding rock mass. The research results are beneficial to the rock burst of surrounding rock of the cavern. The acoustic emission can effectively monitor the stability of the surrounding rock of the cavern. However, the threshold value and the occurrence time of the acoustic emission of the cavern instability changed after the cavern surrounding rock is drilled holes. If the borehole is arranged at the surrounding rock mass, the occurrence time of the cavern instability may be advanced.

25 September 2020 in Geotechnical and Geological Engineering
Verified
Journal Article
Closed access
PDF file
CPChao Peng
Chao Peng
WLWanrong Liu
Wanrong Liu
ZWZhen Wang
Zhen Wang

12 October 2021 in Geofluids
Verified
Journal Article
Open access
PDF file
WLWanrong Liu
Wanrong Liu
CPChao Peng
Chao Peng
BZBaoliang Zhang
Baoliang Zhang
Due to geological structure and artificial disturbance, a large number of joints and fissures are formed in the surrounding rock of an underground tunnel. In order to study the influence of joints on the failure characteristics of tunnels, three test schemes with different joint lengths, joint spacing, and joint positions are designed. The results show that the bearing capacity of the tunnel decreases with the increase in the joint length. With the increase in joint spacing, the bearing capacity of the tunnel decreases first and then increases. The crack propagation law of the three test schemes has experienced four stages: no crack, crack initiation, crack rapid development, and crack gradual reduction. The location of joints has the greatest influence on the failure mode of the tunnel. The crack is most likely to appear at the top of the tunnel and expand along the joint, mainly because it is easy to form tensile stress at the top of the tunnel and compressive stress concentration at the joint tip. Therefore, when excavating the tunnel in the underground space, the influence of joints on the tunnel should be considered. Analyzing the relationship between the tunnel and joints has important practical guiding significance for the control of the surrounding rock of the tunnel. Finally, the failure results of the indoor physical model and numerical model are compared and analyzed. They are in good agreement, which also reflects the rationality of numerical simulation.

1 January 2020 in Latin American Journal of Solids and Structures
Verified
Journal Article
Open access
PDF file
CPChao Peng
Chao Peng
WLWanrong Liu
Wanrong Liu
The existence of holes in rock is one of the key factors for the instability of underground rock mass engineering. Combined with acoustic emission equipment, uniaxial compression tests of rock specimens with different numbers of holes in the rock were carried out. The results show that with the number of holes increases, the value of peak strength and elastic modulus of the rock decrease. The acoustic emission (AE) counts gone through stable, slow increase, a sudden increase and towards zero four stages and there are corresponding to the initial compaction stage, elastic stages, strain hardening stage and post-peak strain softening stage of the stress-strain curves approximately. Based on the AE events, damage variables of rocks were obtained. The damage evolution process of rock can also be divided into three parts, including stable damage stage, slowly increasing damage stage and sharply increasing damage stage. According to Duncan model, the damage variable is introduced to obtain the rock damage constitutive model. No matter it is the pre-peak initial compaction stage, the linear elasticity stage, the strain hardening stage or the post-peak strain softening stage, the fitting curves are in good agreement with the test curves. It also illustrates the rationality of the damage constitutive model.

1 August 2020 in Geotechnical and Geological Engineering
Verified
Journal Article
Closed access
PDF file
CPChao Peng
Chao Peng
WLWanrong Liu
Wanrong Liu