22 December 2023 in Science Advances
Flat optics consisting of nanostructures of high–refractive index materials produce lenses with thin form factors that tend to operate only at specific wavelengths. Recent attempts to achieve achromatic lenses uncover a trade-off between the numerical aperture (NA) and bandwidth, which limits performance. Here, we propose a new approach to design high-NA, broadband, and polarization-insensitive multilayer achromatic metalenses (MAMs). We combine topology optimization and full-wave simulations to inversely design MAMs and fabricate the structures in low–refractive index materials by two-photon polymerization lithography. MAMs measuring 20 μm in diameter operating in the visible range of 400 to 800 nm with 0.5 and 0.7 NA were achieved with efficiencies of up to 42%. We demonstrate broadband imaging performance of the fabricated MAM under white light and RGB narrowband illuminations. These results highlight the potential of the 3D-printed multilayer structures for realizing broadband and multifunctional meta-devices with inverse design.
10 September 2024 in Advanced Optical Materials
A compact and responsive thermoelectric photodetector is introduced for the mid‐infrared. By resonantly coupling mid‐infrared light to a Sb2Te3‐Bi2Te3 thermoelectric junction, a thermocouple is formed that is directly heated by narrow‐band mid‐infrared radiation. Near‐perfect absorption is achieved at this hot junction through the resonantly enhanced coupling of light to free‐electrons in the Bi2Te3 and Sb2Te3 materials. The fabricated devices operate at 3.6 µm and demonstrate a responsivity of 10.2 V W−1, a specific detectivity of 4.6 × 106 cm Hz1/2 W−1, and a bandwidth in the order of 1 kHz. The optimal detection wavelength can be spectrally tuned by changing the resonant cavity dimensions. This work shows a path toward miniaturized mid‐infrared detectors and spectrometers with high sensitivity, responsivity, and bandwidth. Importantly, the device presented here is ideal for industrial production, which it is hoped will provide wider access to mid‐infrared technologies for chemical sensing, medicine, and security.
28 March 2025 in Nanophotonics
Thermoelectric photodetectors are robust alternatives to photodiodes with applications in extreme environments; however, the poor absorptivity of thermoelectric materials limits their photosensitivity. Here, we take a new look at the traditional thermoelectric materials Sb 2 Te 3 and Bi 2 Te 3 in their recently discovered ability to support interband plasmonic resonances in the visible spectrum. We fabricated nanoresonators directly into the thermoelectric materials to improve their optical absorptance through plasmonic field enhancements, leading to improved photo‐thermoelectric conversion. A thermoelectric detector with Sb 2 Te 3 and Bi 2 Te 3 nanostructures demonstrated ∼90 % optical absorptance across the visible spectrum, more than twice that of unpatterned materials. The solid‐state device was fabricated on a substrate and exhibited a response time of 160 µs and a specific detectivity of . Our demonstration that plasmonic and thermoelectric properties can be exploited within the same material could advance photodetectors and other optoelectronic technologies, such as biosensors, solar cells, and integrated spectrometers.
11 February 2025 in Journal of Physics: Materials
Understanding state-dependent crystallisation kinetics is important for the modelling and design of phase change material (PCM)—based devices, such as multi-level switches. We show how the level of amorphousness (disorder) of antimony-telluride (Sb2Te3) can be controlled using pulsed laser heating, and that the recrystallisation temperature strongly depends on the local atomic configurations in the amorphous structure. Indeed, when Sb2Te3 is amorphized with higher laser powers, its subsequent recrystallisation temperature increases by up to 23 °C yet, and counterintuitively the recrystallisation activation energy decreases. This leads to shorter minimum recrystallisation times. This effect is important because it provides a means to switch PCM devices at higher rates through a catalyst-like effect. The optical properties of Sb2Te3 can be gradually tuned by the level of crystallographic disorder. The amorphousness of PCMs provides a further degree-of-freedom to achieve multi-level programmability and tune the switching energy of devices.