Wei Huang

Wei Huang

Auto-generated profile, based on publicly available information

Wei Huang

Department of Materials, ETH Zurich, 8093 Zurich, Switzerland

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2021 in Review of Scientific Instruments
Verified
Journal Article
Open access
PDF file
TMT. Marković
T. Marković
WHW. Huang
W. Huang
PGP. Gambardella
P. Gambardella
SSSebastian Stepanow
Sebastian Stepanow
Scanning tunneling potentiometry allows for studying charge transport on the nanoscale to relate the local electrochemical potential to morphological features of thin films or two-dimensional materials. To resolve the influence of atomic-scale defects on the charge transport, sub-µV sensitivity for the electrochemical potential is required. Here, we present a complete analysis of the noise in scanning tunneling potentiometry for different modes of operation. We discuss the role of various noise sources in the measurements and technical issues for both dc and ac detection schemes. The influence of the feedback controller in the determination of the local electrochemical potential is taken into account. Furthermore, we present a software-based implementation of the potentiometry technique in both dc and ac modes in a commercial scanning tunneling microscopy setup with only the addition of a voltage-controlled current source. We directly compare the ac and dc modes on a model resistor circuit and on epitaxial graphene and draw conclusions on the advantages and disadvantages of each mode. The effects of sample heating and the occurrence of thermal voltages are discussed.

18 January 2024 in Nanoscale
Verified
Journal Article
Open access
PDF file
WHWei Huang
Wei Huang
JSJeong Ah Seo
Jeong Ah Seo
MCMark P. Canavan
Mark P. Canavan
PGPietro Gambardella
Pietro Gambardella
SSSebastian Stepanow
Sebastian Stepanow
Li intercalation is commonly used to enhance the carrier density in epitaxial graphene and mitigate coupling to the substrate. We observe different intercalation phases and measure their local charge transport properties using scanning potentiometry.

1 April 2018 in Review of Scientific Instruments
Verified
Journal Article
Closed access
PDF file
WHWei Huang
Wei Huang
ZLZhean Li
Zhean Li
CXChunkai Xu
Chunkai Xu
JLJian Liu
Jian Liu
CXChunye Xu
Chunye Xu
XCXiangjun Chen
Xiangjun Chen
We report a novel microelectrode-shielding tip (ME tip) for scanning probe electron energy spectroscopy (SPEES). The shielding effect of this tip is studied through comparing the detection efficiency with the normal tip by both experiment and simulation. The results show that the backscattering count rate detected by the SPEES instrument using the normal tip begins to decrease as the tip approaches to the sample surface within 21 μm, while that using the ME tip only starts to drop off within 1 μm. This indicates that the electron energy spectra can be measured with the ME tip at a much closer tip-sample distance. Furthermore, it is also demonstrated that the ME tip can be used to obtain topography of the sample surface in situ simultaneously.

24 October 2017
Verified
Conference Paper
Closed access
PDF file
ZLZhiyong Li
Zhiyong Li
RTRongqing Tan
Rongqing Tan
YWYujie Wang
Yujie Wang
QYQing Qing Ye
Qing Qing Ye
JBJintian Bian
Jintian Bian
WHWei Huang
Wei Huang
Diode pumped alkali laser (DPAL) with hydrocarbon buffer gases has the features of low threshold and high efficiency. The chemical reaction between alkali and hydrocarbon gases affects the life time of DPAL. In this paper, a method based on Fourier transform infrared spectroscopy and Lambert-Beer law is adopted to find a safe temperature at which DPAL runs for a long term. A theoretical model is established to figure out ways to reduce the peak temperature in the cell window. The results indicates that 170 °C is a safe temperature. Although the absorbance of the cell window to the pump light and alkali laser is lower, there is temperature increase. Small light-transmitting area and air blowing on the windows can reduce the peak temperature effectively. Cooling the cell window is essential and critical in a long-term running DPAL.