So-Yeon Ham

So-Yeon Ham

Auto-generated profile, based on publicly available information

So-Yeon Ham

Materials Science and Engineering Program, University of California San Diego, La Jolla, USA

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 September 2021 in Science
Verified
Journal Article
Closed access
DTDarren H. S. Tan
Darren H. S. Tan
YCYu-Ting Chen
Yu-Ting Chen
HYHedi Yang
Hedi Yang
WBWurigumula Bao
Wurigumula Bao
BSBhagath Sreenarayanan
Bhagath Sreenarayanan
YMYing Shirley Meng
Ying Shirley Meng
Silicon anode solid-state batteries: Research on solid-state batteries has focused on lithium metal anodes. Alloy-based anodes have received less attention in part due to their lower specific capacity even though they should be safer. Tan et al . developed a slurry-based approach to create films from micrometer-scale silicon particles that can be used in anodes with carbon binders. When incorporated into solid-state batteries, they showed good performance across a range of temperatures and excellent cycle life in full cells. —MSL

18 September 2024 in Nature Energy
Verified
Journal Article
Open access
PDF file
SPSebastian Puls
Sebastian Puls
ENElina Nazmutdinova
Elina Nazmutdinova
FKFariza Kalyk
Fariza Kalyk
HWHenry M. Woolley
Henry M. Woolley
JTJesper Frost Thomsen
Jesper Frost Thomsen
NVNella M. Vargas-Barbosa
Nella M. Vargas-Barbosa
The interlaboratory comparability and reproducibility of all-solid-state battery cell cycling performance are poorly understood due to the lack of standardized set-ups and assembly parameters. This study quantifies the extent of this variability by providing commercially sourced battery materials—LiNi0.6Mn0.2Co0.2O2 for the positive electrode, Li6PS5Cl as the solid electrolyte and indium for the negative electrode—to 21 research groups. Each group was asked to use their own cell assembly protocol but follow a specific electrochemical protocol. The results show large variability in assembly and electrochemical performance, including differences in processing pressures, pressing durations and In-to-Li ratios. Despite this, an initial open circuit voltage of 2.5 and 2.7 V vs Li+/Li is a good predictor of successful cycling for cells using these electroactive materials. We suggest a set of parameters for reporting all-solid-state battery cycling results and advocate for reporting data in triplicate.

6 April 2024 in Nature Communications
Verified
Journal Article
Open access
PDF file
SHSo-Yeon Ham
So-Yeon Ham
ESElias Sebti
Elias Sebti
ACAshley Cronk
Ashley Cronk
TPTyler Pennebaker
Tyler Pennebaker
GDGrayson Deysher
Grayson Deysher
YMYing Shirley Meng
Ying Shirley Meng
All-solid-state batteries using Si as the anode have shown promising performance without continual solid-electrolyte interface (SEI) growth. However, the first cycle irreversible capacity loss yields low initial Coulombic efficiency (ICE) of Si, limiting the energy density. To address this, we adopt a prelithiation strategy to increase ICE and conductivity of all-solid-state Si cells. A significant increase in ICE is observed for Li1Si anode paired with a lithium cobalt oxide (LCO) cathode. Additionally, a comparison with lithium nickel manganese cobalt oxide (NCM) reveals that performance improvements with Si prelithiation is only applicable for full cells dominated by high anode irreversibility. With this prelithiation strategy, 15% improvement in capacity retention is achieved after 1000 cycles compared to a pure Si. With Li1Si, a high areal capacity of up to 10 mAh cm–2 is attained using a dry-processed LCO cathode film, suggesting that the prelithiation method may be suitable for high-loading next-generation all-solid-state batteries.

9 December 2022 in Energy Storage Materials
Verified
Journal Article
Closed access
SHSo-Yeon Ham
So-Yeon Ham
HYHedi Yang
Hedi Yang
ONOmar Nunez-Cuacuas
Omar Nunez-Cuacuas
DTDarren H.S. Tan
Darren H.S. Tan
YCYu-Ting Chen
Yu-Ting Chen
YMYing Shirley Meng
Ying Shirley Meng

3 July 2024 in Nature Energy
Verified
Journal Article
Closed access
PDF file
GDGrayson Deysher
Grayson Deysher
JOJin An Sam Oh
Jin An Sam Oh
YCYu-Ting Chen
Yu-Ting Chen
BSBaharak Sayahpour
Baharak Sayahpour
SHSo-Yeon Ham
So-Yeon Ham
YMYing Shirley Meng
Ying Shirley Meng

27 February 2026 in Nature Communications
Verified
Journal Article
Open access
PDF file
ACAshley Cronk
Ashley Cronk
XWXiaowei Wang
Xiaowei Wang
JOJin An Sam Oh
Jin An Sam Oh
SHSo-Yeon Ham
So-Yeon Ham
SBShuang Bai
Shuang Bai
YMYing Shirley Meng
Ying Shirley Meng
All-solid-state batteries using sulfur-based positive electrodes (cathodes) offer a cost-effective route to achieve high specific energy. However, low active material utilization and cycle life hinder performance. Here, we demonstrate a positive electrode design that employs sulfide solid-state electrolytes, where a high energy synthesis approach forms a metastable and ionically conductive interphase on the active material surface. This interphase facilitates high active material utilization and contributes capacity with cycling. We also show that tailoring active material particle sizes to the micron-scale improves rate performance and cycling stability. Structural analysis reveals that the substantial volume change of sulfur-based positive electrodes during operation can partially offset that of the negative electrodes, thereby mitigating internal mechanical stress. The combined design principles enable sulfur areal capacities up to 11 mAh cm -2 while maintaining stable cycling at 25 °C. We further demonstrate several specific-energy-focused cell architectures, particularly a Li 2 S anode-free pouch cell that operates under “low stack pressure” of 10 MPa. This work outlines practical design strategies for constructing high-specific-energy all-solid-state batteries for a broad range of emerging applications.