Gheorghe Asachi" Technical University of Iasi, Faculty of Chemical Engineering and Environmental Protection, Dept. of Organic, Biochemical and Food Engineering, D. Mangeron 73, 700050 Iasi, Romania
Auto-generated profile, based on publicly available information
Anca-Irina Galaction
Gheorghe Asachi" Technical University of Iasi, Faculty of Chemical Engineering and Environmental Protection, Dept. of Organic, Biochemical and Food Engineering, D. Mangeron 73, 700050 Iasi, Romania
The complexity of downstream processes for biosynthetic products constitutes a particularity of industrial biotechnologies, especially because of the biosynthetic product high dilution in fermentation broth, their chemical and thermal liability and the presence of secondary products. For these reasons, new separation techniques have been developed and applied to bioseparations. Among them, reactive extraction, pertraction (extraction and transport through liquid membranes) and direct extraction from broths have considerable potential and are required for the further development of many biotechnologies. This review is structured on two parts and presents our original results of the studies on the separation of some biosynthetic products (antibiotics, carboxylic acids, amino acids, alcohols) by reactive extraction in the first part, and by pertraction and direct extraction from broths without biomass filtration in the second. For all the analyzed cases, these extraction techniques simplify the technologies by reducing material and energy consumption, by avoiding product inhibition, by increasing the separation selectivity, therefore decreasing the overall cost of the product
30 January 2013 in Chemical Engineering Communications
This article presents the results of a comparative study of reactive extraction of succinic acid with tri-n-octylamine (TOA) dissolved in solvents with different dielectric constants (dichloromethane, n-butyl acetate, and n-heptane), with and without octan-1-ol addition as phase modifier. The positive effect of octan-1-ol on extraction efficiency was quantified by means of amplification factors. For all studied systems, the addition of octan-1-ol into the solvent phase led to an increase of extraction efficiency, the most important effect being recorded for the solvent with the lowest polarity, namely n-heptane. The maximum value of amplification factor was reached for pH = 6 and indicated an increase of reactive extraction yield of about 1.26 times for dichloromethane, 1.55 times for n-butyl acetate, and 2.88 times for n-heptane.
1 January 2008 in Chemical Industry and Chemical Engineering Quarterly
The comparative study on the reactive extraction of p-aminobenzoic acid with Amberlite LA-2 and D2EHPA in two solvents with different polarity (n-heptane and dichloromethane) indicated that the extractant type and solvent polarity control the extraction mechanism. Thus, the reactive extraction with Amberlite LA-2 occurs by means of the interfacial formation of an aminic adduct with three extractant molecules in low-polar solvent, or of an salt with one extractant molecule in higher polar solvent. Similarly, the extraction with D2EHPA is based on the formation of an acidic adduct with two extractant molecules in n-heptane, or of a salt with one extractant molecule in dichloromethane. The most efficient extraction has been reached for the combination Amberlite LA-2-dichloromethane.
The aim of these experiments is to study the oxygen mass transfer rate by means of the mass transfer coefficient, for a stirred bioreactor and different fermentation broths, using a large domain of operating variables. For quantifying the effects of the considered factors (concentration and morphology of the biomass, specific power input, superficial air velocity surface aeration) on k\a, the experiments were carried out for non-respirating biomass suspensions of Propionibacterium shermanii Saccharomyces cerevisiae and Penicillium chrysogenum, mycelial aggregates (pellets) and free mycelia morphological structures.
1 January 2007 in Environmental Engineering and Management Journal
Although radial impellers, especially the Rushton turbine, are widely used in stirred bioreactors, their applicability is limited by the high apparent viscosities of the broths. For optimizing mechanical mixing by selecting the appropriate impeller for a specific fermentation broth or process, the comparative analysis of the mixing efficiency, energy costs and shear effects on the biocatalysts is required. By means of this analysis, three different combinations of radial impellers for water and viscous simulated broths were selected for attaining optimum mixing in a bioreactor. The proposed impellers combinations offer the most intense and uniformly distributed mixing and the lowest specific power consumption required for reaching a maximum level of mixing time of less than one minute.