Marvin Rades

Marvin Rades

Auto-generated profile, based on publicly available information

Marvin Rades

Department of Animal Ecology & Systematics, Justus Liebig University, Giessen, Germany

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 October 2021 in Global Change Biology
Verified
Journal Article
Open access
PDF file
JRJessica Reichert
Jessica Reichert
AAAngelina L. Arnold
Angelina L. Arnold
NHNils Hammer
Nils Hammer
Ingo B MillerIngo B Miller
Ingo B Miller
MRMarvin Rades
Marvin Rades
serap koşal şahinserap koşal şahin
serap koşal şahin
The pollution of the marine environment with microplastics is pervasive. However, microplastic concentrations in the seawater are lower than the number of particles entering the oceans, suggesting that plastic particles accumulate in environmental sinks. Yet, the exact long‐term sinks related to the “missing plastic” phenomenon are barely explored. Sediments in nearshore biogenic habitats are known to trap large amounts of microplastics, but also the three‐dimensional structures of coral reefs might serve as unique, living long‐term sinks. The main framework builders, reef‐building corals, have been shown to ingest and overgrow microplastics, potentially leading to a deposition of particles in reef structures. However, little is known about the number of deposited particles and the underlying processes determining the permanent deposition in the coral skeletons. To test whether corals may act as living long‐term sink for microplastic, we exposed four reef‐building coral species to polyethylene microplastics (200 particles L−1) in an 18‐month laboratory experiment. We found microplastics in all treatment specimens, with low numbers of particles trapped in the coral tissue (up to 2 particles per cm2) and much higher numbers in the skeleton (up to 84 particles per cm3). The numbers of particles accumulated in the coral skeletons were mainly related to coral growth (i.e., skeletal growth in volume), suggesting that deposition is a regularly occurring stochastic process. We estimate that reef‐building corals may remove 0.09%–2.82% of the bioavailable microplastics from tropical shallow‐reef waters per year. Our study shows for the first time that microplastic particles accumulate permanently in a biological sink, helping to explain the “missing plastic” phenomenon. This highlights the importance of coral reefs for the ecological balance of the oceans and reinforces the need to protect them, not only to mitigate the effects of climate change but also to preserve their ecosystem services as long‐term sink for microplastic.

24 June 2024 in Marine Pollution Bulletin
Verified
Journal Article
Open access
MRMarvin Rades
Marvin Rades
GPGernot Poschet
Gernot Poschet
HGHagen Gegner
Hagen Gegner
serap koşal şahinserap koşal şahin
serap koşal şahin
JRJessica Reichert
Jessica Reichert
The causes of the physiological effects of microplastic pollution, potentially harming reef-building corals, are unclear. Reasons might include increased energy demands for handling particles and immune reactions. This study is among the first assessing the effects of long-term microplastic exposure on coral physiology at realistic concentrations (200 polyethylene particles L-1). The coral species Acropora muricata, Pocillopora verrucosa, Porites lutea, and Heliopora coerulea were exposed to microplastics for 11 months, and energy reserves, metabolites, growth, and photosymbiont state were analyzed. Results showed an overall low impact on coral physiology, yet species-specific effects occurred. Specifically, H. coerulea exhibited reduced growth, P. lutea and A. muricata showed changes in photosynthetic efficiency, and A. muricata variations in taurine levels. These findings suggest that corals may possess compensatory mechanisms mitigating the effects of microplastics. However, realistic microplastic concentrations only occasionally affected corals. Yet, corals exposed to increasing pollution scenarios will likely experience more negative impacts.

10 March 2022
Verified
Preprint
Open access
MRMarvin Rades
Marvin Rades
PSPatrick Schubert
Patrick Schubert
MZMaren Ziegler
Maren Ziegler
MKMartin Kröckel
Martin Kröckel
JRJessica Reichert
Jessica Reichert
Multiple point stirrers are expensive lab equipment (usually €1,000–4,000) and are only offered by a handful of manufacturers. More importantly, the maximum volume per stirring point is minimal in multi-point stirrers and allows the use of small containers only (usually 0.25–0.6 L). However, for many applications, larger volumes per stirring point are needed. Here, we present a building plan to construct a multiple-point stirrer (with twelve stirring points) for larger container volumes (0.8–3 L) for a fraction of the cost of a commercial device. The overall material cost for a 12-point stirrer is around ca. €280. The stirrer is built with axial flow fans equipped with cuboid magnets and controlled via a programmable power supply. In addition, a water bath (ca. €50) can be placed above the stirring points to allow controlled temperature regulation and to complement the function of an incubator.

10 March 2022
Verified
Preprint
Open access
MRMarvin Rades
Marvin Rades
PSPatrick Schubert
Patrick Schubert
MZMaren Ziegler
Maren Ziegler
MKMartin Kröckel
Martin Kröckel
JRJessica Reichert
Jessica Reichert
Multiple point stirrers are expensive lab equipment (usually €1,000–4,000) and are only offered by a handful of manufacturers. More importantly, the maximum volume per stirring point is minimal in multi-point stirrers and allows the use of small containers only (usually 0.25–0.6 L). However, for many applications, larger volumes per stirring point are needed. Here, we present a building plan to construct a multiple-point stirrer (with twelve stirring points) for larger container volumes (0.8–3 L) for a fraction of the cost of a commercial device. The overall material cost for a 12-point stirrer is around ca. €280. The stirrer is built with axial flow fans equipped with cuboid magnets and controlled via a programmable power supply. In addition, a water bath (ca. €50) can be placed above the stirring points to allow controlled temperature regulation and to complement the function of an incubator.