27 September 2017 in Physics of Plasmas
The tearing mode instability is one of the most important dynamic processes in space and laboratory plasmas. Hall effects, resulting from the decoupling of electron and ion motions, can cause fast development and rotation of the perturbation structure of the tearing mode. A high-accuracy nonlinear magnetohydrodynamics code is developed to study Hall effects on the evolution of tearing modes in the Tokamak geometry. It is found that the linear growth rate increases with the increase in the ion skin depth and the self-consistently generated rotation can greatly alter the dynamic behavior of the double tearing mode.
1 December 2021 in Computer Physics Communications
20 September 1991 in Journal of Geophysical Research
A two‐dimensional magnetohydrodynamic code is used to study impulsive penetration processes that occur when a plasma irregularity in the magnetosheath, modeled as a field‐aligned filament, impinges on the day side magnetopause. If the magnetic fields in the magnetosheath and magnetosphere are parallel or antiparallel, then a filament in the magnetosheath can always penetrate into the magnetosphere. However, if the fields in the magnetosheath and magnetosphere are not aligned, then a filament can only penetrate into the magnetosphere when its initial kinetic energy density exceeds the magnetic energy density attributed to the transverse component of the magnetic field by a factor of 50. In this case, the magnetospheric field lines reconnect behind the filament, thereby trapping it within the magnetosphere. Otherwise, the increasing magnetic stress in front of the filament will eventually stop the filament from further penetration. For typical parameters found at the dayside magnetopause, the threshold condition obtained from this two‐dimensional model predicts that penetration is possible only when the angle between the fields is within approximately 5° of parallel or antiparallel. During the penetration process, velocity vortices are observed both inside the filament and in the external plasma. Either increased β within the magnetosphere, or the larger plasma density at the magnetopause associated with antiparallel magnetic fields, will act to reduce the penetration velocity.
30 October 2019 in International Journal of Computational Fluid Dynamics
In this paper, the OpenACC heterogeneous parallel programming model is successfully applied to modification and acceleration of the three-dimensional Tokamak magnetohydrodynamical code (CLT). Through combination of OpenACC and MPI technologies, CLT is further parallelised by using multiple-GPUs. Significant speedup ratios are achieved on NVIDIA TITAN Xp and TITAN V GPUs, respectively, with very few modifications of CLT. Furthermore, the validity of the double precision calculations on the above-mentioned two graphics cards has also been strictly verified with m/n = 2/1 resistive tearing mode instability in Tokamak.
1 May 2016 in Physics of Plasmas
The influence of driven current on the resistive tearing mode is studied systematically using a three-dimensional toroidal magnetohydrodynamic code. A uniform driven current with Gaussian distribution in the radial direction is imposed around the unperturbed rational surface. It is found that the driven current can locally modify the profiles of the current and safety factor, such that the tearing mode becomes linearly stable. The stabilizing effect increases with the increase of the driven current or the decrease of its width , unless an excessively large driven current reverses the magnetic shear near the rational surface and drives other instabilities such as double or triple tearing modes. The stabilizing effect can be negligible or becomes reversed if the maximum driven current density is not at the unperturbed rational surface.
23 September 2010 in Journal of Geophysical Research
Nonlinear evolution of resistive tearing mode with different sub‐Alfvenic shear flow is investigated using incompressible magnetohydrodynamics simulations. The sub‐Alfvenic shear flow can have either stabilization or destabilization effects on the tearing mode development, which is mostly determined by the shear flow thickness (av). The shear flow tends to boost the tearing mode instability when the thickness of the shear flow is above av ∼ 0.35a (where a is the normalization unit). The boosting effect of the shear flow on the tearing mode becomes strongest at av ∼ 0.6a. But the strength of the boosting and suppressing effects is controlled by the asymptotic velocity (V0) of the shear flow. The suppressing and boosting effects of the shear flow increase with increase of the shear flow velocity. The kinetic energy associated with initial shear flow is reduced when the shear flow has a boosting effect on the tearing mode growth.