Sant Ram Chauhan

Sant Ram Chauhan

Auto-generated profile, based on publicly available information

Sant Ram Chauhan

National Institute Of Technology Hamirpur

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

12 November 2012 in Advanced Materials Research
Verified
Journal Article
Closed access
PDF file
SCS.R. Chauhan
S.R. Chauhan
STSunil Thakur
Sunil Thakur
In this paper the friction and wear characteristics of vinylester and vinylester composites have been investigated under dry sliding conditions for different applied normal load, sliding speed and sliding distance. The experiments have been carried on a pin on disc arrangement at normal room temperature conditions. The influence of friction and wear parameters like normal load, speed, sliding distance and percentage of filler content on the friction and wear rate has been investigated. In this study, a plan of experiments based on the techniques of Taguchi was performed to acquire data in a controlled way. An orthogonal array L27 (313) and Analysis of variance (ANOVA) were applied to investigate the influence of process parameters on the coefficient of friction and sliding wear behaviour of these composites. The Taguchi design of experiment approach eliminates the need for repeated experiments and thus saves time, material and cost. The results showed that with increase in the applied normal load and sliding speed the coefficient of friction and specific wear rate decreases under dry sliding conditions. It is also found that a thin film formed on the counterface seems to be effective in improving the tribological characteristics. The results showed that the inclusion of cenosphere as filler materials in vinylester composites will increase the wear resistance of the composite significantly.

1 January 2012 in International Journal of Machining and Machinability of Materials
Verified
Journal Article
Closed access
STSunil Thakur
Sunil Thakur
SCS.R. Chauhan
S.R. Chauhan
Titanium alloy (grade-5) is one of the materials extensively used in the aerospace industry due to its excellent properties such as high specific strength and corrosion resistance. It also presents problems as it is extremely difficult material to machine. The cost associated with titanium machining is also high due to lower cutting speeds, feed, and depth of cut. In this study, the Taguchi method is used for design of experiment and analysis to find the optimal cutting parameters. An orthogonal array, L

1 September 2011
Verified
Conference Paper
Closed access
SISiddhartha
Siddhartha
SCSant Ram Chauhan
Sant Ram Chauhan
VAVarun
Varun
NSNaveen Sharma
Naveen Sharma
Nowadays, the interest of researcher growing in the field of optimization of solar systems in order to improve the thermal performance by reducing friction losses and increasing heat transfer rates either using optimization techniques or improving system design by introducing roughness elements. In case of solar air heater, the working fluid is air which reduces the probability of corrosion and also decreases the weight of collector and correspondingly reduces the cost. The thermal performance of solar air heater is low which can be increased by rising heat transfer rates which can be obtained by using high flow rates. In this work, simulated annealing algorithm has been implemented to optimize the thermal performance of flat plate solar air heater and predict the optimized set of design and operating parameters. The concept of simulated annealing based on the physical annealing process in statistical mechanics which governs first law of thermodynamics. The algorithm for the optimization is developed as well as simulation is carried out based upon the code developed in MATLAB. The design and operating parameters which affect the thermal performance are wind velocity, irradiance; tilt angle, mass flow rate, ambient temperature, emissivity of plate and number of glass cover plates. In this work the optimized set of these parameters are obtained and the optimized thermal performance is evaluated. The results obtained show that the maximum thermal performance is 72.48 % for three number of glass plate at an irradiance of 600 W/m2. The final results obtained from this technique are compared with other optimization techniques like PSO, GA and found to be satisfactory. These results are also compared with the experimental results.

30 October 2026 in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Verified
Journal Article
Closed access
STSaurabh Thakur
Saurabh Thakur
SCSant Ram Chauhan
Sant Ram Chauhan
PSParnika Shrivastava
Parnika Shrivastava
Incremental forming offers a flexible approach for manufacturing patient specific implants with complex asymmetric geometries. Titanium is ideal for biomedical implants due to biocompatibility and corrosion resistance but exhibits limited room temperature formability. Elevated temperatures can improve formability during single point incremental forming of titanium sheets, but the material response under such forming conditions is still not fully understood. In this study, a heat assisted single point incremental forming setup with cartridge heaters was developed to fabricate a patient-specific cranial implant geometry from commercially pure titanium grade 2 sheets at 204 °C. Geometric accuracy was evaluated using material thickness distribution, springback and geometric deviation analysis. The deformation behaviour during elevated temperature single point incremental forming was investigated through microstructural and texture evolution using electron backscatter diffraction analysis at progressive forming depths. The formed implant exhibited relatively uniform thickness distribution and limited springback, with a maximum bend angle of 5.991°. Microstructural analysis revealed significant grain refinement, with the average grain size decreasing from 16 to 1 μm and the fraction of low-angle grain boundaries increasing from 18.6% to 32.2%. Texture evolution was characterized by progressive weakening of the initial rolling texture and increasing orientation dispersion, with only a weak tendency towards alignment along the { 1 ¯ 2 1 ¯ 8 } fibre at higher forming depths. The electron backscatter diffraction observations indicate progressive grain subdivision, substructural evolution and continuous redistribution of crystallographic orientations during elevated-temperature single point incremental forming. The observed microstructural features are also suggestive of localized recovery processes at higher forming depths.