6 February 2024 in Journal of the European Ceramic Society
JJJosé Fernando Valera Jiménez
José Fernando Valera Jiménez
+1
1 July 2023 in Journal of Physics: Energy
Carbon coated-LiFePO4 (LFP) is a strong candidate as lithium-ion battery (LiB) cathode due to the combination of safe operation, stable electrochemical performance and positive environmental impact as does not depend on Co, which is toxic and a critical raw material. In this work, we report the development of binder-free LFP cathodes fabricated by fused filament fabrication (FFF) technology. Several novel carbon-LFP filaments have been developed to 3D-print LiB cathodes, analysing both the carbon to LFP ratio in the formulation and also the impact of the carbon source used as current collector, i.e. glassy carbon (GC) microspheres or carbon black (CB), in the electrochemical performance. LFP remained stable upon debinding and sintering at temperatures as low as 500 °C as determined by x-ray diffraction. The conductivity of 3D printed LFP monoliths was 2.06 × 10−4 S∙cm−1 at 50 °C, which is fairly close to that of LFP produced via conventional processing. This is mainly attributed to the preservation of the carbon coating around the LFP particles after debinding and sintering under controlled Ar atmospheres. The LFP-based electrodes containing CB or GC microspheres as conductive additives exhibited specific capacities of 150 mAh g−1, and over 95% coulombic efficiency after 100 cycles, showing no significant performance losses. These results largely exceed the performances reported for previous LFP-based electrodes produced via FFF as the non-active binder is removed upon fabrication.
14 February 2024 in Journal of Physics: Energy
Additive manufacturing techniques have the potential to promote a paradigmatic change in the electrode fabrication processes for lithium-ion batteries (LiBs) as they may offer alternative component designs to boost their performance or to customise the application. The present research work explores the use of low-cost fused filament fabrication (FFF) 3D printing to fabricate Li4Ti5O12 (LTO) mesh electrodes in the search for enlarged electrochemically active areas. Using different nozzle diameters (ND), we have 3D printed several mesh electrodes that after sintering allow an increase in the surface to volume ratio by up to ≈290% compared to conventional flat cylindrical geometries. As the conventional route to produce 3D printed meshes, i.e. stacking of consecutive layers with a 90° rotation, leads to problems of vertical misalignment that may affect the electrical contact, we have developed a new compact design that maximises the contact between layers. All the 3D printed mesh electrodes with thicknesses of 400 and 800 μm, exhibit electrochemical performance very close to those of thin (70 μm) electrodes, e.g. 175 mAh g−1 at C/2 in the case of ND = 100 μm, which is the theoretical capacity value for LTO. At higher C-rates, 800 μm-thick mesh electrodes with larger ND exhibit a marked drop in the reversible capacity (28 mAh g−1 at 8 C), although the values obtained improve notably those of the equivalent thick solid electrode (almost null at 8 C). The compact design demonstrated superior performance at high C-rates, improving by ≈70% the results of the best conventional mesh electrode at 8 C for 800 μm electrodes. These results highlight the potential of FFF-3D printing to generate novel high aspect ratio geometries and the impact of design and printing parameters on the performance of LiB electrode materials. Exploring alternative efficient geometries may facilitate the integration of thick electrodes in high energy density LiBs.
12 June 2026 in Journal of Physics: Energy
In the present work, polymer-ceramic composite filaments with 70%–75%wt load of NMC622 and NMC622/carbon black (CB) have been developed to produce high-voltage electrodes for Li-ion battery applications via fused filament fabrication (FFF) 3D printing. In the search for higher capacities, binder-free electrodes were obtained after thermal treatments to eliminate the organic polymer and produce ceramics with a certain level of mechanical strength (800 °C for 6 h in air). NMC622 decomposes under non-oxidizing atmospheres at low temperatures, whilst oxidizing conditions would prevent the use of carbon-based additives to improve the electronic conductivity of the electrodes. Therefore, an alternative strategy that considers partial debinding at moderate temperatures (≈300 °C) was also proposed. Both strategies led to the production of electrodes exhibiting electrochemical performances close to those of conventionally processed NMC622-based cathodes. 3D printed full ceramic (binder free) NMC622 electrodes yielded reversible capacities of up to 147 mAh g at C/10, i.e. 89% capacity retention, although the performance was significantly lower at higher rates (i.e. C/2). On the other hand, the partially debinded NMC622 electrodes containing 10%wt of CB performed extended cycling runs with up to ≈130 mAh g and CE ≈99% at C/10 and also rather competitive values up to C/2 (≈70 mAh g after 500 cycles). Furthermore, the CB preservation was crucial under more demanding conditions to perform adequately up to 2 C, recovering the starting capacity at C/10. Therefore, these results demonstrate that NMC-based electrodes can be fabricated using FFF-3D printing technologies after applying optimized strategies for debinding and sintering.