Sungwoo Lim

Sungwoo Lim

Auto-generated profile, based on publicly available information

Sungwoo Lim

School of Physical Sciences, The Open University, Milton Keynes, UK

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 January 2012 in Materials and Structures
Verified
Journal Article
Open access
PDF file
TLT. T. Le
T. T. Le
SAS. A. Austin
S. A. Austin
SLS. Lim
S. Lim
RBR. A. Buswell
R. A. Buswell
AGA. G. F. Gibb
A. G. F. Gibb
TTT. Thorpe
T. Thorpe
This paper presents the experimental results concerning the mix design and fresh properties of a high-performance fibre-reinforced fine-aggregate concrete for printing concrete. This concrete has been designed to be extruded through a nozzle to build layer-by-layer structural components. The printing process is a novel digitally controlled additive manufacturing method which can build architectural and structural components without formwork, unlike conventional concrete construction methods. The most critical fresh properties are shown to be extrudability and buildability, which have mutual relationships with workability and open time. These properties are significantly influenced by the mix proportions and the presence of superplasticiser, retarder, accelerator and polypropylene fibres. An optimum mix is identified and validated by the full-scale manufacture of a bench component.

1 January 2012 in Automation in Construction
Verified
Journal Article
Open access
SLS. Lim
S. Lim
RBR.A. Buswell
R.A. Buswell
TLT.T. Le
T.T. Le
SAS.A. Austin
S.A. Austin
AGA.G.F. Gibb
A.G.F. Gibb
TTT. Thorpe
T. Thorpe
This article was published in the journal, Automation in Construction [© Elsevier B.V.] and the definitive version is available at: http://dx.doi.org/doi:10.1016/j.autcon.2011.06.010Additive manufacturing in construction is beginning to move from an architect’s modelling tool to delivering full-scale architectural components and elements of buildings such as walls and facades. This paper discusses large-scale additive manufacturing processes that have been applied in the construction and architecture arena and focuses on ‘Concrete Printing’, an automated extrusion based process. The wet properties of the material are critical to the success of manufacture and a number of new criteria have been developed to classify these process specific parameters. These criteria are introduced and key challenges that face construction scale additive manufacturing are presented

1 March 2012 in Cement and Concrete Research
Verified
Journal Article
Open access
TLT.T. Le
T.T. Le
SAS.A. Austin
S.A. Austin
SLS. Lim
S. Lim
RBR.A. Buswell
R.A. Buswell
RLR. Law
R. Law
TTT. Thorpe
T. Thorpe
This article was published in the journal, Cement and Concrete Research [© Elsevier Ltd.] and the definitive version is available at: http://dx.doi.org/10.1016/j.cemconres.2011.12.003This paper presents the hardened properties of a high-performance fibre-reinforced fine-aggregate concrete extruded through a 9 mm diameter nozzle to build layer-by-layer structural components in a printing process. The printing process is a digitally controlled additive method capable of manufacturing architectural and structural components without formwork, unlike conventional concrete construction methods. The effects of the layering process on density, compressive strength, flexural strength, tensile bond strength and drying shrinkage are presented together with the implication for mix proportions. A control concrete (mould-cast specimens) had a density of approximately 2250 kg/m3, high strength (107 MPa in compression, 11 MPa in flexure) and 3 MPa in direct tension, together with a relatively low drying shrinkage of 175 μm (cured in water) and 855 μm (cured in a chamber at 20 °C and 60% relative humidity) at 184 days. In contrast well printed concrete had a density of 2350 kg/m3, compressive strength of 75–102 MPa, flexural strength of 6–17 MPa depending on testing direction, and tensile bond strength between layers varying from 2.3 to 0.7 MPa, reducing as the printing time gap between layers increased. The well printed concrete had significantly fewer voids greater than 0.2 mm diameter (1.0%) when compared with the mould-cast control (3.8%), whilst samples of poorly printed material had more voids (4.8%) mainly formed in the interstices between filaments. The additive extrusion process was thus shown to retain the intrinsic high performance of the material

1 October 2017 in Advances In Space Research
Verified
Journal Article
Closed access
SLSungwoo Lim
Sungwoo Lim
VPVibha Levin Prabhu
Vibha Levin Prabhu
MAMahesh Anand
Mahesh Anand
LTLawrence A. Taylor
Lawrence A. Taylor

1 October 2016 in Additive Manufacturing
Verified
Journal Article
Open access
SLSungwoo Lim
Sungwoo Lim
RBRichard A. Buswell
Richard A. Buswell
PVPhilip J. Valentine
Philip J. Valentine
DPDaniel Piker
Daniel Piker
SASimon A. Austin
Simon A. Austin
XKXavier De Kestelier
Xavier De Kestelier
This paper was accepted for publication in the journal Additive Manufacturing and the definitive published version is available at http://dx.doi.org/10.1016/j.addma.2016.06.004In this paper, a non-conventional way of additive manufacturing, curved-layered printing, has been applied to large-scale\ud construction process. Despite the number of research works on Curved Layered Fused Deposition Modelling (CLFDM)\ud over the last decade, few practical applications have been reported. An alternative method adopting the CLFDM principle,\ud that generates a curved-layered printing path, was developed using a single scripting environment called Grasshopper\ud – a plugin of Rhinoceros®\ud . The method was evaluated with the 3D Concrete Printing process developed at Loughborough\ud University. The evaluation of the method including the results of simulation and printing revealed three principal benefits\ud compared with existing flat-layered printing paths, which are particularly beneficial to large-scale AM techniques: (i)\ud better surface quality, (ii) shorter printing time and (iii) higher surface strengths

29 June 2011 in Proceedings of the 37th International Symposium on Automation and Robotics in Construction (isarc)
Verified
Conference Paper
Open access
SLSungwoo Lim
Sungwoo Lim
RBRichard Buswell
Richard Buswell
TLThanh Le
Thanh Le
RWRene Wackrow
Rene Wackrow
SASimon Austin
Simon Austin
TTTony Thorpe
Tony Thorpe
I.A.A.R.C. - International Association for Automation and Robotics in Construction Civil Engineering