The aim of this study was to investigate the effects of process parameters on tensile strength for PLA specimens produced by fused deposition modeling (FDM). For this purpose, two different density rates (20% and 100%), printing speeds (100 and 130 mm/s), and nozzle temperatures (180 and 220oC) with three different hatching patterns including elliptical and diagonal (Gyroid, Cross 3D ve Grid) were selected. In the study, higher tensile stress was obtained at a rate of 100%, compared to a 20% density rate. When the samples with a 20% density rate are compared among themselves, the highest tensile stress value obtained was measured as 38.76 MPa for the Grid-patterned specimen produced at a nozzle temperature of 2200C and printing speed of 100 mm/s. Statistical analysis was also done for specimens with a 20% density rate. As a result of the variance analysis (ANOVA) method, the confidence level was achieved as 96%. When comparing in terms of specific strength, it was determined that the closest pattern to the full-filled sample with a specific strength of 5,893 MPa/gr was Cross 3D-patterned sample with a value of 5.458 MPa/gr.
28 December 2025 in International Journal of 3D Printing Technologies and Digital Industry
Composite railway sleepers are increasingly adopted as durable, low-maintenance, and sustainable alternatives to conventional materials, offering enhanced long-term performance and adaptability under demanding service conditions. In parallel, 3D printing has become an innovative and cost-effective research tool for developing scaled railway components. This study investigates, for the first time, the dynamic behavior of scaled, semi-functional P90-type composite railway sleeper prototypes fabricated by additive manufacturing. The 1:13.33-scale ABS specimens were tested using Experimental Modal Analysis (EMA) in vertical, lateral, and longitudinal orientations under free-free boundary conditions. A detailed Finite Element Model (FEM) was developed in ANSYS, incorporating measured unit weight, accelerometer mass, and elastic support stiffness. Iterative back-analysis was performed to align FEM predictions with EMA-measured fundamental resonance frequencies, yielding excellent correlation at E = 2595 MPa and G = 1120 MPa, with a maximum individual mode deviation of 0.959 % and a total three-mode deviation of 1.601 %. The validated FEM demonstrates partial similitude, a principle long applied in aerospace and mechanical engineering to achieve dynamically consistent results using scaled prototypes. Overall, this study establishes a preliminary methodological foundation for future modal topology optimization (MTO) and full-scale correlation studies, serving as a case-study framework for extending similitude-based dynamic characterization of railway sleeper systems. The proposed methodology can also be broadly applied to investigate and enhance the dynamic behavior of structural components in civil, mechanical, and materials engineering.
30 April 2023 in İmalat Teknolojileri ve Uygulamaları
Additive manufacturing is a manufacturing method that includes systems that produce using many different methods. The most widely used and accessible methods of additive manufacturing can be listed as Fused Deposition Modeling (FDM), Selective Laser Sintering (SLS) and UV light assisted Stereolithography (SLA). Today, it is quite easy to produce thermoplastic products suitable for direct use in low quantities with these three methods. In addition, the production success of the parts produced in geometric difficulties also increases this demand. The most important problem is the lack of sufficient studies and information about the strength limits, surface quality and costs of the parts produced for additive manufacturing methods with such advantages. In this study, the comparison of three different production methods in terms of surface roughness, strength and cost is discussed in order to eliminate this deficiency in the literature. For this purpose, the tensile strength and surface roughness values of the samples produced using FDM, SLS and SLA methods were determined. In addition, cost analyzes were made depending on the production time of the produced samples. In the study, the lowest cost was obtained in the SLA material with a value of $ 0.19. Again, the lowest values were obtained for the samples produced from SLA material, with a production time of 17 minutes and a surface roughness of 1.96µm compared to other methods. However, when evaluated in terms of strength, the highest strength value was obtained as 57.67 N/mm2 in the FDM method.
26 June 2019 in Mühendislik Bilimleri ve Tasarım Dergisi
Metal ve plastik enjeksiyon ile seri imalat yapan işletmelerin kilit elemanları kalıplardır. Büyük baskı adetlerinin getirdiği yorgunluk, aşınma ve baskı sırasında kalıp arasında sık parça sıkışması neticesinde oluşan yüksek kuvvetler kalıp elemanlarının zamanla deforme olmasına neden olmaktadır. Bu durumda kalıbın revize edilmesi veya bozuk parçaların yeniden imal edilesi gerekmektedir. Doğrusal olmayan geometrideki parçaların imalatı için bilgisayar ortamında üç boyutlu(3D) katı model verileri gerekmektedir. Eğer bu verilere ulaşılmaz ise genellikle Tersine Mühendislik (TM) uygulaması yapılması gerekmektedir. Bu çalışmada, tan itriyat sanayi ve tic. şti. firmasına ait teknik resimleri ve 3D katı model verisi olmayan atıl durumdaki bir kalıbının doğrusal olmayan yüzeye sahip bozuk bir parçasının TM uygulaması içerisinde 3D tarayıcı ile tarama yaparak iki boyutlu (2D) tarama verileri elde edilmiş. Çalışmada, TM uygulamasında geometrinin uzun süren matematiksel bağıntılara ihtiyaç olmadan kısa süre içerisinde SolidWorks Bilgisayar Destekli Tasarım programında (BDT) aşınmış olan bölgeleri kolay teknikler ile düzelterek katı model elde edilmiştir. Elde edilen katı model bilgisayar destekli imalat (CAM) yazılımı SolidCAM programında imalata hazırlanmış ve CNC dik işleme tezgâhında imal edilmiştir. İmal edilen parça tekrar kalıba monte edilerek kalıptan başarılı bir baskı alınmıştır. Aynı zamanda yeniden üretilen kalıp elemanı ile kalıba ait olamayan başka bir ara ürün ile montajlı çalıştığı bilinmektedir. Bu ara ürününde 2D tarama verileri ile karşılaştırmalı sonucu paylaşılmıştır. Çalışmada, seri bir TM uygulaması yaparak yeni kalıp yapım maliyeti olmadan ve örnek bir sürdürülebilir imalata örnek üretim yapılmıştır.