1 January 2021 in International Journal of Aviation, Aeronautics, and Aerospace
The work in this paper aims to increase the maximum lift coefficient of the airfoil by implementing the co-flow jet concept on NACA 0018 airfoil and also to investigate the performance of co-flow jet (CFJ) airfoil. To conduct numerical solution, RANS equations have been solved for 2D incompressible and unsteady flow using the Spalart-Allmaras turbulence model. The suction surface of the airfoil is modified by placing the injection slot near the leading edge and the suction slot near the trailing edge. A small mass of air is withdrawn into the airfoil suction slot, pressurized by a pumping system located inside the airfoil, and re-injecting into the injection slot tangentially to the main stream flow. The CFJ airfoil is enhancing the aerodynamic lift coefficient significantly compare to the baseline airfoil. And also, the numerical analysis is carried out to investigate the effect of the location of injection and suction slot. And it is observed that the aerodynamic lift coefficient of CFJ airfoil is increasing with varying the injection slot away from the leading edge.
1 September 2023 in Physics of Fluids
This research aims to explore the effect of the co-flow jet (CFJ) airfoil injection jet velocity, injection height, and injection mass flow rate on the aerodynamic coefficient through numerical analysis. Five distinct circumstances are generated by adjusting the jet velocity, injection height, and mass flow rate, and each of the cases underwent numerical investigation. For this computational analysis, Reynolds averaged Navier–Stokes (RANS) solver has been utilized by employing the Spalart–Allmaras turbulence model, and the flow is treated as incompressible. The higher injection slots reduce the coefficient of lift (CL) due to poor aerodynamic shape, which can be overcome by injecting higher jet velocities, whereas lower jet velocities injecting into lower injection slots do not raise the CL even though they have streamlined aerodynamic shape. Hence, even if CFJ airfoils with poor geometry perform less aerodynamically, this problem is not intractable because it can be solved by injecting high jet velocities; meanwhile, injecting low velocities will result in reduced aerodynamic performance for CFJ airfoils with good geometry. The CFJ airfoil with the highest jet velocity and lowest injection slot increases the CL by a maximum of 65% compared to the baseline airfoil, which is higher than all other CFJ airfoils taken into consideration.
1 May 2021 in Journal of Physics: Conference Series
Bio-mimicry is one of the leading fields of research that has been around since the early ages of science. Aerospace industry, especially, takes most of its design inspiration from the aquatic life. In this paper a breed of flying fish scientifically known as Exocoetidae, Cypselurus Hiraii has been chosen to study. The aerodynamic characteristics of the fish were studied experimentally in a wind tunnel previously, but the plausibility of its design application in the aerospace industry hasn’t been explored yet. Therefore, in the present study the cross-section of the fish in the side view has been traced and its aerodynamic performance as a 2D infinite wing has been examined in ANSYS R15 (FLUENT). The performance of this fish inspired shape has been compared to the properties of conventional aerofoils in terms of coefficient of lift and coefficient of drag.
23 March 2023 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
The induced drag created by wingtip vortices has a significant impact on aircraft performance. Winglets are wingtip extensions that are intended to reduce the creation of vortices and increase the fuel efficiency. The present study is based on analyzing different winglets planform for aircraft at various angles of attack (AOA) to improve the aerodynamic efficiency. The Finite Volume Method in pressure-based solver along with the Realizable k - ɛ turbulence model, with standard atmospheric boundary conditions is used to do the CFD computations in ANSYS Fluent. According to the findings, an optimized BLERAK (Blended + Raked) winglet from the present study has a substantial impact on aerodynamic efficiency when compared to conventional winglets, and it is projected to yield a higher lift-to-drag ratio. The blerak winglets model gives 1.5 to 2% drag reduction than the other winglet models at angle of attack variations of 8°, 12° and 16°.
1 November 2017 in Journal of Applied Fluid Mechanics
24 October 2011 in Applied Mechanics and Materials
This paper the optimum wing planform for flapping motion is investigated by measuring the lift and drag characteristics. A model is designed with a fixed wing and two flapping wings attached to its trailing edge. Using wind tunnel tests are conducted to study the effect of angle of attack (smoke flow visualization technique). The test comprises of measuring the aerodynamic forces with flapping motion and without it for various flapping frequencies and results are presented. It can be possible to produce a micro air vehicle which is capable of stealthy operations for defence requirements by using these experimental data.