Bilim Atli-Veltin

Bilim Atli-Veltin

Auto-generated profile, based on publicly available information

Bilim Atli-Veltin

The Pennsylvania State University, Pennsylvania, USA

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2018 in Cryogenics
Verified
Journal Article
Closed access
BABilim Atli-Veltin
Bilim Atli-Veltin

20 December 2024 in Composites Part A: Applied Science and Manufacturing
Verified
Journal Article
Open access
SGS. Gomarasca
S. Gomarasca
DPDaniël Peeters
Daniël Peeters
BAB. Atli-Veltin
B. Atli-Veltin
TST. Slange
T. Slange
GRG. Ratouit
G. Ratouit
CDClemens Dransfeld
Clemens Dransfeld

1 April 2012
Verified
Conference Paper
Closed access
BABilim Atli-Veltin
Bilim Atli-Veltin
HLHuang Ling
Huang Ling
SZSusan Zhao
Susan Zhao
SNSander Noijen
Sander Noijen
JCJo Caers
Jo Caers
YYYuming Ye
Yuming Ye
FE models were developed to investigate the effect of processing and 3PB on the mechanical reliability of the embedded components. The results focus on the central region of resistor and capacitor. Local effects around the vias or copper layers are not considered. During processing, after processing and after bending compressive stresses are observed on both the embedded capacitor and the resistor. These results indicate that the risk of cracking on the components is low; however, the compressive stresses should be compared to the critical compressive stress limits of these materials. Similar results were obtained for the capacitor and the resistor. Due to the difference in the material properties (mainly CTE) higher compressive stresses are observed in the Alumina (resistor) compared to the Ceramic (capacitor). During processing, cooling causes the horizontal compressive stresses to increase, and heating causes them to decrease. Before the PCB is subjected to 3PB, the components possess compressive stresses which are caused by the lamination process. This is an advantage of the embedded components over a surface mounted component, where tensile stresses occur on the components. The 1mm bending loading causes the horizontal compressive stresses to reduce slightly. Bending the strip to 20 mm still does not cause the horizontal compressive stresses to diminish. The overall conclusion is that embedding the components is favorable to mounting a component on the surface of a PCB with respect to risk for component cracks. A high stiffness region was included in the model to represent the fiber glass around the components. This model was subjected to lamination process. The results show that the compressive stresses occurring on the components due to lamination is slightly affected by this region. Overall conclusions do not change with existence of a stiffer area above the components.

27 January 2013 in The Aeronautical Journal
Verified
Journal Article
Closed access
PDF file
BAB. Atli-Veltin
B. Atli-Veltin
FGF. Gandhi
F. Gandhi
The in-plane crushing and energy absorption of sandwiched honeycomb cores with facesheets are examined through finite element simulations. Assuming no debonding between the facesheet and honeycomb core (which would be the case if manufacturing techniques such as brazing are used to produce very strong bonds between the facesheeet and the core), intracellular buckling mode for thin facesheets, and wrinkling mode for thick facesheets are observed. In the dimpling mode, deformation is governed by the core, honeycomb vertical cell walls do not deform, and the inclined wall deformation does not vary through the cell depth. In the wrinkling mode, deformation is governed by the facesheet, the vertical cell walls deform significantly, and the inclined cell wall deformation varies through the cell depth. Increasing cell angle increased Specific Energy Absorption (SEA) for honeycombs with thin facesheets. Decreasing vertical cell wall length increased SEA for honeycombs with thick facesheets. Increasing wall thickness and decreasing core depth increased SEA for honeycombs with thin and thick facesheets. With geometric changes, SEA increased ~3 times over the baseline configurations. For a given keel beam dimensions, using fewer rows of larger cells reduces the effective non-dimensional core-depth, thereby increasing the effect of the facesheet and the SEA significantly. The SEA of sandwiched honeycombs with facesheets in in-plane crushing appears to be competitive with, or better than, SEA honeycombs in out-of-plane crushing.