1 June 2000 in The Journal of the Acoustical Society of America
The one-port source characteristics in a duct system, viz., source impedance and strength, can be determined by using the four-load method. In this paper, to avoid the instability problem of the conventional four-load method, a new formulation for the multiload method has been proposed, which employs an error function based on the linear, time-invariant source model. It is shown that the method is less sensitive to input errors compared to the previous methods. For a 10% input error, the proposed method yields a relative error in the source resistance that is about 1/100 times smaller than for the conventional method. The effectiveness of the present method is demonstrated by two test examples, a loudspeaker and a blower, each operating in a duct. It is observed that the conventional and least-squares methods result in large errors, whereas the present method yields far better agreement with the actual source parameters, as measured by the direct method. The present method is then used to obtain the source parameters on the exhaust side of an operating internal combustion engine. The radiated sound spectrum from the exhaust opening is predicted by using the measured source parameters and the calculated result agrees very well with the measured one.
1 March 2013 in The Journal of the Acoustical Society of America
The time domain boundary element method (TBEM) to calculate the exterior sound field using the Kirchhoff integral has difficulties in non-uniqueness and exponential divergence. In this work, a method to stabilize TBEM calculation for the exterior problem is suggested. The time domain CHIEF (Combined Helmholtz Integral Equation Formulation) method is newly formulated to suppress low order fictitious internal modes. This method constrains the surface Kirchhoff integral by forcing the pressures at the additional interior points to be zero when the shortest retarded time between boundary nodes and an interior point elapses. However, even after using the CHIEF method, the TBEM calculation suffers the exponential divergence due to the remaining unstable high order fictitious modes at frequencies higher than the frequency limit of the boundary element model. For complete stabilization, such troublesome modes are selectively adjusted by projecting the time response onto the eigenspace. In a test example for a transiently pulsating sphere, the final average error norm of the stabilized response compared to the analytic solution is 2.5%.
22 June 2020 in Applied Physics Letters
For the design of duct silencers, one should satisfy the essential constraints on the sound attenuation band, additional volume, and backpressure. For wideband sound attenuation, various acoustic metamaterials (AMM) using multiple resonators have been proposed. However, they often do not satisfy the spatial constraint, and the blocking of the conduit makes them impractical. This study proposes a compact silencing AMM unit for wideband sound reduction without deteriorating the mechanical performance. Previous works on the stacked micro-perforated panels (MPP) with different backing air gaps provide the basic idea of this work, which reveals the benefit of multiple resonators in adjusting the bandwidths to attain a wideband attenuation characteristic. The resistive element is also exploited in the MPP for suppressing the acoustic transparency of the detuned resonators. The formulated theoretical design method is tested by using a resonant unit cell configured with a serial connection of quadruple MPP layers, each air gap with a length of 30 mm and a uniform sectional area of 8 × 8 mm2. For minimizing the occupied volume, each cell surrounds the outer periphery of the main duct by folding, and the cell entry is flush-mounted on the duct wall. The test is conducted with the main duct of 30 × 30 mm2, and the attached 50 cells are arranged periodically with a 10-mm interval. The additional width of the duct is less than 1% of the wavelength. The measured power transmission coefficient is less than 0.2 for the range of 0.4–4.05 kHz, which agrees well with the prediction.
20 March 2019 in IEEE/ASME Transactions on Mechatronics
The pattern of bending vibration on a thin plate is controlled to create a virtual speaker and baffle set. An actuator array at the plate edges is used to generate the bending wave to form the desired vibration pattern. The speaker zone is rendered to maintain a uniform phase as a speaker, whilst the rest of the plate is kept to be tranquil to serve as a baffle. From the rendering information and the potential positions of the actuators, the actuator gains are determined in an inverse manner. Vibration on a finite plate is modelled by the superposition of Green's functions between the actuators and field points, which depend on the speaker size and location, and the shape and material of plates. Parametric studies are conducted to determine the effect of those functions on the radiated sound characteristics. Simulation results show that the radiated sound spectrum features similar dips at some Helmholtz numbers would cause the deterioration of sound quality and reproducibility. These dips appear because of two typical reasons. The first condition is that the Helmholtz number becomes about 3.8 and 7.0, corresponding to the low-order radial modes of the circular speaker zone having circumferential nodes. The other arises when the distance between the speaker center and the plate edges is an integer multiple of the bending wavelength. The proposed method is tested on the roof panel of a car to compensate for the poor response of the built-in speakers. It is shown that the virtual speaker has a uniform phase in the speaker zone and that the low-frequency performance is reinforced well.
15 May 2011 in International Journal of Automotive Technology
1 May 2010 in Journal of Sound and Vibration