Yunpeng Zhang

Yunpeng Zhang

Auto-generated profile, based on publicly available information

Yunpeng Zhang

State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072, China

Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2026 in Materials
Verified
Journal Article
Open access
PDF file
YZYunpeng Zhang
Yunpeng Zhang
ZLZuo Li
Zuo Li
SCShilong Che
Shilong Che
XLXin Lin
Xin Lin
XLXufei Lu
Xufei Lu
Wall thickness affects local heat accumulation during laser powder bed fusion (LPBF), but its role in governing the as-built martensitic morphology and tensile response of near-α TA15 alloy remains unclear. In this study, TA15 walls with thicknesses from 0.5 mm to 30 mm were fabricated under identical LPBF parameters. Optical microscopy, scanning electron microscopy, electron backscatter diffraction, tensile testing, fractography, and finite-element thermal simulation were used to correlate wall-thickness-dependent cyclic reheating with α′ lath evolution and mechanical behavior. Increasing wall thickness promoted α′ lath coarsening and the formation of colony-like lath structures with enlarged similarly oriented regions. The average α′ lath width increased from approximately 0.28 μm in the 0.5-T specimen to 1.55 μm in the 30-T specimen. The yield strength reached a maximum of 972.3 ± 5.29 MPa in the 1-T specimen, whereas elongation increased from 9.5 ± 0.6% to 17.8 ± 1.7% with increasing wall thickness. These results indicate a strong correlation between wall-thickness-dependent cyclic reheating, α′/α lath coarsening, lath-network evolution, and tensile-property variation in LPBF-fabricated TA15 alloy.

YZYunpeng Zhang
Yunpeng Zhang
SCShilong Che
Shilong Che
JHJunfeng He
Junfeng He
XLXin Lin
Xin Lin
XLXufei Lu
Xufei Lu
Unsupported and weakly supported overhang features remain a critical challenge in laser powder bed fusion (LPBF) due to their strong susceptibility to geometric degradation, residual stress accumulation, and part distortion. In this study, bridge-shaped structures with four different arch sizes are fabricated to systematically investigate geometry-dependent macroscopic forming quality, stress evolution, and distortion behavior. Experimental results show that increasing arch size leads to progressive thickness reduction at the arch bottom and eventual overhang closure loss, indicating a monotonic deterioration in geometric fidelity. A thermo-mechanically coupled finite element model is developed and calibrated using 3D scanning measurements of warpage, achieving a maximum deviation below 0.03 mm between predicted and measured displacements. Numerical analyses reveal that larger arch sizes promote local heat accumulation and reduced cooling rates beneath the arch, which reduce the instantaneous load-bearing capacity of the material and increase its susceptibility to downward deformation. Meanwhile, arch size significantly influences the establishment of structural continuity and stress transfer during printing; incomplete closure in large arches interrupts load-bearing paths and alters stress redistribution at intermediate stages, whereas similar stress evolution trends are observed once geometric continuity is achieved. These findings demonstrate that arch closure acts as a key structural transition controlling stress transmission and distortion development during LPBF, thereby providing mechanistic insight into geometry-induced defects and offering quantitative guidance for the design of unsupported features in additively manufactured components.

YZYunpeng Zhang
Yunpeng Zhang
JHJunfeng He
Junfeng He
XLXin Liao
Xin Liao
SCShilong Che
Shilong Che
XLXin Lin
Xin Lin
XLXufei Lu
Xufei Lu
Geometric distortion remains a major obstacle to achieving high dimensional accuracy in laser powder bed fusion (LPBF), especially for complex thin-walled components with heterogeneous structural constraint. In this study, a finite element simulation-driven geometric compensation strategy was applied and validated for an LPBF-fabricated winged annular funnel structure (WAFS). A transient thermo-mechanically coupled finite element model was established to predict the distortion behavior during fabrication and validated by 3D scanning measurements, showing good agreement in both global deformation trend and local distribution characteristics. The simulation results indicated that the distortion of the WAFS was dominated by the combined constraint effect of the wing-like features and the baseplate, resulting in a non-uniform and symmetric deformation pattern. Based on the validated displacement field, an inverse-mapping method was used to construct a compensated geometry for re-fabrication. The compensated WAFS exhibited a substantially reduced deformation level, and the overall geometric distortion was reduced by more than 85% after a single compensation iteration. The present results demonstrate that finite element simulation-driven geometric compensation provides an efficient and practical route for improving the dimensional accuracy of the investigated WAFS, while reducing dependence on repeated trial-and-error optimization.

12 August 2026 in Metals
Verified
Journal Article
Open access
PDF file
YZYunpeng Zhang
Yunpeng Zhang
SCShilong Che
Shilong Che
XLXin Lin
Xin Lin
XLXufei Lu
Xufei Lu
Laser powder bed fusion (LPBF)-fabricated TA15 titanium alloy commonly exhibits a fine acicular lath morphology, which has frequently been interpreted as martensitic in previous studies and is generally associated with high strength and limited plastic accommodation. In this study, LPBF-TA15 specimens were annealed at 800, 900, and 950 °C for 2 h, followed by furnace cooling, and subsequently subjected to secondary annealing at 550 °C for 4 h. Each sequentially annealed condition was compared with its corresponding single-step condition to distinguish retained microstructural differences from the tensile-property changes associated with the subsequent treatment. Microstructural evolution and monotonic tensile properties at room temperature and 300–600 °C were investigated. Annealing at 800 °C retained a relatively fine lamellar morphology. Increasing the initial annealing temperature to 900 and 950 °C produced progressively larger apparent lath and colony scales, with the most pronounced coarsening observed at 950 °C. Tensile results are reported as mean ± standard deviation. After secondary annealing, A800-S550 exhibited the highest mean room-temperature strength among the three secondary-annealed conditions, with a yield strength of 1045.0 ± 2.6 MPa, an ultimate tensile strength of 1116.7 ± 2.3 MPa, and an elongation of 14.3 ± 0.7%. From 300 to 600 °C, its yield strength decreased from 701.0 ± 3.2 to 493.6 ± 9.8 MPa, while its ultimate tensile strength decreased from 823.5 ± 3.8 to 585.6 ± 7.1 MPa; the elongation at 600 °C was 19.0 ± 1.8%. In this study, microstructural inheritance refers to the persistence, after the common 550 °C treatment, of differences in lath and lamellar-colony scales and EBSD boundary characteristics established during initial annealing. The secondary-annealed conditions retained distinct microstructural scales and exhibited different tensile responses; however, a unique causal relationship between the retained morphology and the magnitude of the property changes was not established. Residual stress, post-heat-treatment oxygen variation, and quantitative texture evolution were not independently evaluated. The conclusions are limited to the heat-treatment schedules and monotonic tensile conditions examined in this study.

11 August 2026 in Materials
Verified
Journal Article
Open access
PDF file
YZYunpeng Zhang
Yunpeng Zhang
XNXiaojiong Nie
Xiaojiong Nie
XLXin Liao
Xin Liao
XLXin Lin
Xin Lin
XLXufei Lu
Xufei Lu
Residual stresses generated during laser powder bed fusion (LPBF) can cause substantial distortion in slender structures, compromising dimensional accuracy and structural reliability. This study tests the hypothesis that, under identical nominal processing conditions, geometry-dependent stiffness and constraint govern how the evolving thermally induced stress field is redistributed and manifested as warpage after support removal. Bridge-type TA15 titanium alloy cantilever specimens with different spans, thicknesses, and support densities were fabricated by LPBF, and their post-cut warpage was quantified by three-dimensional scanning. A coupled thermo-mechanical finite element model was validated against the measured deformation profiles and subsequently used to examine simulated stress evolution during deposition and redistribution after support removal. Cantilevers with different spans approached similarly high simulated surface tensile-stress plateaus in the constrained as-built state but exhibited markedly different measured warpage after cutting, showing that the as-built stress magnitude alone does not reliably rank post-release deformation. Increasing span reduced global flexural resistance and enlarged the effective bending arm, whereas increasing thickness enhanced flexural rigidity and suppressed curvature even when relatively high localized stress was retained. With the total support volume held constant, changing support density altered the system-level constraint through the combined effects of support-leg stiffness, support spacing, local thermal and mechanical response, and deformation compatibility. Together, these results provide an experimentally supported process-structure interpretation of LPBF cantilever distortion across controlled variations in span, thickness, and support distribution.