27 January 2023 in Ukrainian Chemistry Journal
Due to the ability of LiFePO4 (LFP) to be charged with large currents, LFP batteries are widely used in household appliances and electric vehicles, so the recycling of spent LFP batteries becomes an urgent need. First, they contain toxic components of electrolyte that cannot be buried in landfills; secondly, the cost of lithium which contains in the electrode material continuously increases, and therefore its return to circulation is profitable and expedient. To achieve this goal, much attention is paid to hydrometallurgical processing based on the chemical extraction of Li2CO3 and FePO4 during the regeneration of the electrode material. Here we report on the wet chemistry recycling of used LFP batteries. The main task of the work was to simplify the LiFePO4 regeneration process by leaching with a solution of citric acid due to the elimination of the stage of isolation of Li2CO3 and FePO4, i.e. without selective separation of the filtrate components. The source of spent LiFePO4 was an industrial lithium iron phosphate battery failed due to an internal short circuit. It was found that using citric acid in the ratio H3Cit:LiFePO4=0.5:1, it is possible to efficiently and quickly separate the electrode material from the aluminum current collector. Further pyrolysis and heat treatment of the citrate solution makes it possible to obtain a high-purity LiFePO4/C composite material without extraneous impurities, except for amorphous carbon, which is formed during the pyrolysis of iron (II) and lithium citrates and the thermal decomposition of the binding material in an inert atmosphere. The specific capacity of the LiFePO4/C composite material recovered by the proposed method (145 mA∙h/g) insignificantly differs from that of commercial analogues. This, in our opinion, indicates good prospects of the lithium-iron phosphate regeneration method proposed in this paper.
27 April 2024 in Journal of Electrochemical Science and Engineering
Based on both the economic and environmental points of view, processing used lithium-ion batteries (LIBs) is of great importance. The valuable components contained in LIB (cathode, anode and current collectors) generate high interest in solving the problem of resource deficiency and reducing environmental destruction due to overexploitation. The starting anode material extracted from a used lithium iron phosphate battery is a mixture of graphite, acetylene carbon black, and polymer binder. Reusing this material in lithium batteries without additional cleaning is impractical owing to poor electrochemical characteristics and the presence of impurities. To achieve effective regeneration, the recycled anode material is first treated in a nitric acid solution to remove copper foil and lithium ions with electrolyte interaction products formed during battery operation. The next step is heat treatment of the material, which allows the removal of acetylene soot and polymer glue binder. The tests showed sufficiently high values of the specific capacity of recycled graphite (~330 mA h g-1 at 0.1 C), which are comparable to commercial materials and meet the requirements of reuse.
13 June 2024 in Journal of Electrochemical Science and Engineering
Due to shortening the duration of the process and possibility to obtain crystals of smaller and uniform size, microwave heating is considered an effective and promising tool for the synthesis of LiMn2O4, a valuable cathode material for lithium-ion batteries. However, electrochemical characteristics of LiMn2O4 obtained with its help are almost completely absent and do not allow for drawing a sound conclusion regarding advantages and drawbacks of microwave processing. Here we present a description of the microwave-assisted citric acid aided synthesis, characterization and electrochemical performance of LiMn2O4. The disclosure of detailed working protocols enabling one to manufacture samples tolerant to extremely high currents is the main novelty of this paper. Specifically, our material sustains current loads up to 40 C (5920 mA g-1) and completely recovers after cycling at harsh conditions.
25 June 2026 in Ukrainian Chemistry Journal
This study presents an electrochemical comparison of Li||LiMn₀.₇Fe₀.₃PO₄ coin cells using two different polymers as binders: PVDF and the water-soluble binder NV‑1A. The charge/discharge curves obtained at a current rate of 0.05 C exhibit two well-defined plateaus at approximately 3.5 V and 4.1 V, corresponding to the Fe²⁺/Fe³⁺ and Mn²⁺/Mn³⁺ redox pairs, respectively. The capacity ratio of these plateaus is about 7:3, which matches the Mn/Fe ratio in the pristine material. The specific capacity of the coin cells with different binders falls within the range of 137–141 mAh·g⁻¹, which is consistent with the manufacturer’s specifications for the material. However, upon the first cycles, the coin cells with NV‑1A binder exhibit a slightly lower specific capacity. This is attributed to the possible formation of Li₃PO₄ particles on the electrode surface, which leads to a decrease in specific capacity upon the initial cycles but improves the overall stability upon prolonged cycling. The first-cycle coulombic efficiency is 96.0 % for PVDF and 94% for NV‑1A, increasing to 99.5% ± 0.1 % upon further cycling for both systems. Increasing the charge/discharge current density leads to a decrease in the specific capacity of Li||LiMn₀.₇Fe₀.₃PO₄ electrodes. This decrease is more pronounced for PVDF. At 0.5 C, the specific capacity reaches 68 mAh·g⁻¹ for PVDF and 85 mAh·g⁻¹ for NV‑1A. Cyclic stability tests reveal that, despite the lower initial capacity of the NV‑1A based coin cells, their capacity fade rate is only 0.1 % per cycle at 0.1 C, compared with 0.45 % for PVDF. Consequently, after 75 cycles, the NV‑1A coin cells exhibit superior capacity retention. These findings are further discussed in the context of electrode degradation mechanisms upon cycling.
12 November 2026 in Journal of Electrochemical Science and Engineering
Recycling spent batteries, particularly lithium-ion batteries, is becoming a global priority. Among the various recycling approaches, hydrometallurgy is one of the most useful methods. Among the many chemical compositions of cathode materials, ternary layered oxides warrant particular attention in recycling technology, making them more suitable candidates than other cathode materials. During hydrometallurgical leaching, various carboxylic acids are employed as solvents; however, oxalic acid deserves special consideration due to its high selectivity for lithium extraction. Nickel, cobalt, and manganese oxalates are practically insoluble in water and exist as the corresponding crystal hydrates. When a solution of transition metal sulphates, derived from cathode powder, is treated with a mixture of oxalic acid, the lithium remains in solution as a mixture of lithium sulphate and oxalate, while the transition metals are converted into their corresponding oxalates. In this process, a significant increase in the mass of the precipitate is observed, corresponding to the formation of oxalates. Thus, oxalic acid enables selective extraction of lithium from the “black mass” of lithium-ion batteries based on layered transition metal oxides. Moreover, the resulting mixture of transition metal oxalates, after minor compositional adjustments, can be directly reused for the resynthesis of ternary layered oxides. This paper presents methods for the hydrometallurgical processing of NCM523 (lithium nickel-cobalt-manganese oxide with a 5:2:3 molar ratio of Ni:Co:Mn) cathode material and its subsequent re-synthesis using transition metal and lithium oxalates. The physicochemical characteristics and electrochemical properties of the regenerated NCM523 electrodes are evaluated from the perspective of their potential reuse in rechargeable power sources.
14 March 2023 in Material Science & Engineering International Journal
The “pompon” graphene was obtained by the new modified controlled detonation gas synthesis tested as an anode of LIBs. Processing of Raman spectra by changing the position of the G-band shows the presence of a mixture of 2, 3 and 4-layer graphene structures.The results of the surface area measurement by the BET method have been shown the limited availability of the “pompons” for the penetration of lithium ions between its layers.Subsequent thermomechanical activation leads to partial “delamination” of the pompon and the production of both separate and 2-layer sheets of graphene, which is reflected in a sharp increase in its specific surface area. The specific capacity of graphene, as an anode of LIBs, increases in the range M0 < M20 < M40 and reaches of 500 mAh•g-1 at a current density of 37.2 mA•g-1 for the best M40 sample. The obtained values of specific capacity are 1.5 times higher than similar values for graphite-based anodes.