7 February 2023 in IEEE Transactions on Vehicular Technology
Trajectory tracking and stability control are two essential functions of autonomous vehicles, and there is inevitable mutual interference between them, especially under extreme conditions. Towards addressing this challenge, this paper proposes a novel cooperative strategy of trajectory tracking and stability control for four-wheel independent drive (4WID) autonomous vehicles. An adaptive trajectory tracking controller is designed based on the model predictive control (MPC) theory, in which the tire cornering stiffness is modified in real-time leverages the lateral force estimated by the square-root cubature Kalman filter (SCKF). Then, the vehicle stability controller is designed based on the sliding mode control (SMC), in which the tire force saturation constraint and the relative weight of yaw rate and sideslip angle are considered. Furthermore, a weight adaptive criterion with normalized stability index is defined to develop the cooperative strategy of trajectory tracking and stability control. The feasibility and adaptability of the proposed method to different extreme conditions are verified by hardware-in-the-loop (HIL) test and CarSim-Simulink co-simulation. Finally, an experimental case is presented to demonstrate the realizability of the proposed method.
17 May 2021 in Vehicle System Dynamics
In order to identify the road friction coefficient of the left and right sides of the vehicle more accurately, this paper presents an estimation framework based on a novel tyre model and modified square-root cubature Kalman filter (SCKF). To begin with, a novel tyre model is proposed by adaptively calculating the longitudinal and lateral stiffness and the effective friction coefficient. The tyre forces calculated by this model are more accurate than those calculated by the Brush model. Then, to avoid the influence of abnormal measurement noise on the estimation effect, we develop an improved SCKF (ISCKF) algorithm based on the maximum correntropy criterion. The algorithm can update the measurement noise covariance adaptively. Furthermore, a real-time estimation scheme of road friction coefficient is designed by combining the vehicle dynamics model with the proposed novel tyre model and ISCKF algorithm. Finally, the performance of the presented method is verified by the co-simulation of CarSim and MATLAB/Simulink. The results show that the designed estimation scheme not only has excellent robustness in the case of abnormal measurement noise interference but also has good adaptability to the uncertainty of road friction coefficients distribution.
14 March 2022 in Journal of the Franklin Institute
9 July 2021 in Measurement Science and Technology
For a state estimation problem of nonlinear system, the square-root cubature Kalman filter (SCKF) is an effective method when the noise statistical characteristics are known. However, the performance of SCKF often degrade significantly in the face of uncertain noises interference, particularly in case of measurement or system failure. In this paper, we focus on improving the accuracy and robustness of SCKF under irregular noise. First, a weighted adaptive SCKF (WASCKF) algorithm is presented with moving window method. The WASCKF can improve the accuracy of SCKF by adaptively adjusting the covariances of measurement noise and process noise. Next, in order to further improve the robustness of WASCKF against the abrupt abnormal noise, a correction adaptive SCKF (CASCKF) algorithm based on fault detection mechanism is proposed. The CASCKF algorithm can detect whether there is a fault according to a statistical function of Chi-square distribution, and can judge and carry out the necessary correction processing by using an isolate rule. Finally, the performance of CASCKF is verified by numerical experiments of autonomous vehicle target tracking problem. The results show that the proposed CASCKF algorithm has good accuracy and robustness even with sudden abnormal noise interference.
12 October 2020 in Journal of Low Frequency Noise, Vibration and Active Control
An 8-DOF three-axle vehicle model with semi-active suspension is built in this paper, of which the accuracy is verified through simulations and experiments. Based on the optimal control theory, the linear quadratic Gaussian controller for semi-active suspension is designed with 10 evaluation indicators. Considering the deficiency of linear quadratic Gaussian control weight coefficients based on experience, analytic hierarchy process is employed to determine the weight coefficients of each indicator. The control effect is analyzed through MATLAB/Simulink. The adaptability of proposed control strategy under 25 driving conditions is analyzed with different road grades and speeds. The driving condition of “70 km/h travel speed on the road of grade B” is selected, under which the comparison of vehicle responses between semi-active suspension and passive suspension is made. Results show that the vertical vibration is effectively diminished by using semi-active suspension with linear quadratic Gaussian controller. Compared with passive suspension, the riding comfort is improved and the adverse effect on handling stability is eliminated. The three-axle vehicle with semi-active suspension has good adaptability to various working conditions.