The search for high-capacity, low-cost electrode materials for sodium-ion batteries is a significant challenge in energy research. Among the many potential candidates, layered compounds such as MoS2 have attracted increasing attention. However, such materials have not yet fulfilled their true potential. Here, we show that networks of liquid phase exfoliated MoS2 nanosheets, reinforced with 20 wt % single-wall carbon nanotubes (SWNTs), can be formed into sodium-ion battery electrodes with large gravimetric, volumetric, and areal capacity. The MoS2/SWNT composite films are highly porous, electrically conductive, and mechanically robust due to its percolating carbon nanotube network. When directly employed as the working electrode, they exhibit a specific capacity of >400 mAh/g and volumetric capacity of ∼650 mAh/cm3. Their mechanical stability allows them to be processed into free-standing films with tunable thickness up to ∼100 μm, corresponding to an areal loading of 15 mg/cm2. Their high electrical conductivity allows the high volumetric capacity to be retained, even at high thickness, resulting in state-of-the-art areal capacities of >4.0 mAh/cm2. Such values are competitive with their lithium-ion counterparts.
Advances in lithium ion batteries would facilitate technological developments in areas from electrical vehicles to mobile communications. While 2-dimensional systems like MoS2 are promising electrode materials due to their potentially high capacity, their poor rate-capability and low cycle-stability are severe handicaps. Here we study the electrical, mechanical and lithium storage properties of solution-processed MoS2/carbon nanotube anodes. Nanotube addition gives up to ×1010 and ×40 increases in electrical conductivity and mechanical toughness respectively. The increased conductivity results in up to a ×100 capacity enhancement to ~1200 mAhr/g (~3000 mAhr/cm3) at 0.1 A/g, while the improved toughness significantly boosts cycle stability. Composites with 20 wt% nanotubes combined high reversible capacity with excellent cycling stability (e.g. ~950 mAh/g after 500 cycles at 2 A/g) and high-rate capability (~600 mAh/g at 20 A/g). The conductivity, toughness and capacity scaled with nanotube content according to percolation theory while the stability increased sharply at the mechanical percolation threshold. We believe the improvements in conductivity and toughness obtained after addition of nanotubes can be transferred to other electrode materials such as silicon nanoparticles.
Several critical issues, such as the shuttling effect and the sluggish reaction kinetics, exist in the design of high‐performance lithium–sulfur (Li‐S) batteries. Here, it is reported that nitrogen doping can simultaneously and significantly improve both the immobilization and catalyzation effects of Co9S8 nanoparticles in Li‐S batteries. Combining the theoretical calculations with experimental investigations, it is revealed that nitrogen atoms can increase the binding energies between LiPSs and Co9S8, and as well as alleviate the sluggish kinetics of Li‐S chemistry in the Li2S6 cathode. The same effects are also observed when adding N‐Co9S8 nanoparticles into the commercial Li2S cathode (which has various intrinsic advantages, but unfortunately a high overpotential). A remarkable improvement in the battery performances in both cases is observed. The work brings heteroatom‐doped Co9S8 to the attention of designing high‐performance Li‐S batteries. A fundamental understanding of the inhibition of LiPSs shuttle and the catalytic effect of Li2S in the newly developed system may encourage more effort along this interesting direction.
Organic electrode materials with environmental friendliness and design flexibility at the molecular level are promising substitutes for inorganic materials as cathodes for sodium ion batteries (SIBs). However, traditional organic electrode materials usually exhibit poor cycling stability, mainly due to the dissolution of small organic molecules in electrolytes, and low electronic conductivity. Herein, conjugated porous polyimide poly(2,6-diaminoanthraquinone) benzamide (CP-PDAB) was prepared from 2,6-diaminoanthraquinone and pyromellitic dianhydride by a simple polycondensation reaction. The obtained CP-PDAB has disordered aggregates with a porous and loose structure, facilitating the penetration of the electrolyte and buffering the volume change during charging/discharging. The conjugated skeleton with electron delocalization offers the benefits of structural stability, insolubility in electrolyte and high electronic conductivity. When evaluated as a cathode for SIBs, it can retain a high reversible discharge capacity of 141 mA h g−1 at 500 mA g−1 for 100 cycles, and can maintain a high specific capacity of 71 mA h g−1 at 10 A g−1 after 500 cycles. This work demonstrates the potential application of organic materials containing a conjugated skeleton, porous and loose structure for next-generation electrochemical energy storage devices.