Surface active amine-functionalized silica coated magnetic iron oxide nanoparticles were prepared by a simple two-step process for adsorbing CO2 gas from aqueous medium. First, oleic acid (OA) coated iron oxide magnetic particles (denoted as Fe3O4-OA) were prepared by a simple coprecipitation method. Then, the surface of the Fe3O4-OA particles was coated with silica by using tetraethyl orthosilicate. Finally, aminated Fe3O4/SiO2-NH2 nanoparticles were concomitantly formed by the reactions of 3-aminopropyl triethoxysilane with silica-coated particles. The formation of materials was confirmed by Fourier transform infrared spectral analysis. Transmission electron microscopic analysis revealed both spherical and needle-shaped morphologies of magnetic Fe3O4/SiO2-NH2 particles with an average size of 15 and 68.6 nm, respectively. The saturation magnetization of Fe3O4/SiO2-NH2 nanoparticles was found to be 33.6 emu g-1, measured by a vibrating sample magnetometer at ambient conditions. The crystallinity and average crystallite size (7.0 nm) of the Fe3O4/SiO2-NH2 particles were revealed from X-ray diffraction data analyses. Thermogravimetric analysis exhibited good thermal stability of the nanoadsorbent up to an elevated temperature. Zeta potential measurements revealed pH-sensitive surface activity of Fe3O4/SiO2-NH2 nanoparticles in aqueous medium. The produced magnetic Fe3O4/SiO2-NH2 nanoparticles also exhibited efficient proton capturing activity (92%). The particles were used for magnetically recyclable adsorption of aqueous CO2 at different pH values and temperatures. Fe3O4/SiO2-NH2 nanoparticles demonstrated the highest aqueous CO2 adsorption efficiency (90%) at 40 °C, which is clearly two times higher than that of nonfunctionalized Fe3O4-OA particles.
Simple one-step synthesis of magnetic Fe 3 O 4 @PABA nanoadsorbents for magnetically recyclable adsorption of anionic azo dye pollutants from wastewater.
Synthesis of a bisphosphonated polyelectrolytic stabilizer to in situ fabricate and functionalize Fe 3 O 4 nanoparticles and their pH-dependent hemolysis and bone-cell adhesion.
Easily accessible robust synthesis of metallic nanoparticles (NPs) and their colloidal stabilization via successive surface functionalization with desired molecules are crucial for catalytic applications. In this research, tannic acid (TA)-functionalized bismuth (Bi)-based novel NPs were prepared via a simple in situ aqueous reduction of Bi3+ ions for the catalytic reduction of azo groups. The synthesis, morphology, and structure of Bi/TANPs were confirmed through spectroscopic, electron microscopic and X-ray diffraction analyses. The Bi/TANPs comprise Bi, carbon, oxygen and sodium as building components and possess a high negative surface charge of −58 mV, colloidal dispersity, thermal stability and crystalline structure. The Bi/TANPs are almost spherical shaped with an average diameter of 33 nm. The surface of the catalyst is mesoporous with a high specific surface area of 267 m2 g−1. The designed Bi/TANPs exhibit pH-specific affinity for azo dye molecules and reduced azo moieties in the presence of aqueous NaBH4 without requiring any hydrogen gas supply. The catalytic reduction efficiencies of Bi/TANPs against methylene blue and Congo red are almost 100%. These reduction reactions are very fast owing to the presence of TA moieties on the catalyst surface, which facilitate direct electron transfer to azo groups, and follow a pseudo-first-order kinetic model. The catalyst is mechanically recyclable, and shows a minimal loss (<3%) of its initial efficiency until the fifth cycle. This study not only developed an efficient catalyst for the remediation of azo dye-contaminated water, but also offers novel insights into the synergistic effects of TA and glycerin on the reduction mechanism of aqueous Bi3+ ions and the concomitant colloidal stabilization of Bi NPs.