Jingbo Zhao

Jingbo Zhao

Auto-generated profile, based on publicly available information

Jingbo Zhao

Beijing University of Chemical Technology

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 April 2021 in ACS Sustainable Chemistry & Engineering
Verified
Journal Article
Closed access
KLKuan Liang
Kuan Liang
GZGanggang Zhang
Ganggang Zhang
JZJingbo Zhao
Jingbo Zhao
LSLing Shi
Ling Shi
JCJue Cheng
Jue Cheng
JZJunying Zhang
Junying Zhang

1 September 2014 in RSC Advances
Verified
Journal Article
Closed access
PDF file
YDYong Deng
Yong Deng
SLSuqing Li
Suqing Li
JZJingbo Zhao
Jingbo Zhao
ZZZhiyuan Zhang
Zhiyuan Zhang
JZJunying Zhang
Junying Zhang
WYWantai Yang
Wantai Yang
A simple non-isocyanate route synthesizing aliphatic thermoplastic poly(ether urethane)s (PEUs) with good thermal and mechanical properties is described. Melt transurethane polycondensation of 1,6-bis(hydroxyethyloxy carbonyl amino)hexane (BHCH) with two ethylene glycol oligomers, i.e. triethylene glycol (3EG) and tetraethylene glycol(4EG), was conducted, and high molecular weight PEUs were prepared. The PEUs were characterized by gel permeation chromatography, FT-IR, 1H-NMR, differential scanning calorimetry, thermogravimetric analysis, wide angle X-ray scattering, and tensile tests. The PEUs exhibited Mn above 32 000, Mw above 54 300, Tg ranging from 11.2 °C to 28.2 °C, Tm from 103.7 °C to 150.6 °C, and initial decomposition temperature over 237.4 °C. A PEU prepared at a BHCH/4EG molar ratio of 5 : 1 exhibited the best mechanical properties with tensile strength of 32.82 MPa and strain at break of 151.82%. Some urea linkages were formed due to a back-biting side reaction in the transurethane polycondensation.

7 October 2009 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
PDF file
CHChao Qun Huang
Chao Qun Huang
SLSi Yang Luo
Si Yang Luo
SXShao Yi Xu
Shao Yi Xu
JZJing Bo Zhao
Jing Bo Zhao
SJSheng Ling Jiang
Sheng Ling Jiang
WYWan Tai Yang
Wan Tai Yang

16 December 2014 in RSC Advances
Verified
Journal Article
Closed access
PDF file
SLSuqing Li
Suqing Li
JZJingbo Zhao
Jingbo Zhao
ZZZhiyuan Zhang
Zhiyuan Zhang
JZJunying Zhang
Junying Zhang
WYWantai Yang
Wantai Yang
A simple non-isocyanate route for synthesizing aliphatic thermoplastic polyurethane-ureas (TPUUs) and thermoplastic polyureas (TPUreas) is presented. Melt transurethane polycondensation of isophorone diamine or diethylene glycol bis(3-aminopropyl) ether with bis(hydroxyethyl) hexanediurethane, bis(hydroxyethyl) isophoronediurethane or bis(hydroxyethyl) piperazinediurethane was conducted at 170 °C under a reduced pressure of 3 mmHg. A series of thermoplastic TPUUs and TPUreas were prepared, and were characterized by gel permeation chromatography, FT-IR, 1H-NMR, differential scanning calorimetry, thermogravimetric analysis, and tensile testing. The TPUUs and TPUreas have an Mn up to 14 900 g mol−1, an Mw up to 43 700 g mol−1, Tg between −18.6 °C and 116.8 °C, and an initial decomposition temperature of over 222.3 °C. A flexible TPUU exhibits a melting temperature of 77.7 °C, a tensile strength of 6.46 MPa, and an elongation at break of 180.20%.

16 February 2016 in Industrial & Engineering Chemistry Research
Verified
Journal Article
Closed access
SLSuqing Li
Suqing Li
ZSZhihui Sang
Zhihui Sang
JZJingbo Zhao
Jingbo Zhao
ZZZhiyuan Zhang
Zhiyuan Zhang
JZJunying Zhang
Junying Zhang
WYWantai Yang
Wantai Yang

26 June 2007 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
PDF file
JZJing Bo Zhao
Jing Bo Zhao
KLKai Yong Li
Kai Yong Li
WYWan Tai Yang
Wan Tai Yang