Murat Demir Aydin

Murat Demir Aydin

Auto-generated profile, based on publicly available information

Murat Demir Aydin

Erzurum Teknik Universitesi

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 December 2018 in The Journal of Adhesion
Verified
Journal Article
Closed access
ŞÇŞ. Çitil
Ş. Çitil
IBİ. Bozkurt
İ. Bozkurt
MAM. Demir Aydın
M. Demir Aydın
This study evaluates adhesively bonded pipes with curved-surface lap joints subjected to internal pressure. To test the effects of curvilinear radii on the strength of the adhesive bond, steel pipes (St 37) with curved surfaces of the same lap length and different radii were bonded with the adhesive DP 810. Internal pressure was applied until failure and the mechanical behavior of the bonds was examined experimentally and numerically. Numerical analyses used Cohesive Zone Materials Models (bilinear, exponential, and mixed mode) to estimate the strength of the adhesive bonding. The parameters required for material models were determined experimentally and then experiments were run to verify the models with the finite elements. The results show that the curvature radius has considerable influence on failure pressure.

7 November 2024
Verified
Preprint
Open access
GHGoudarz Ghanizadeh Hesar
Goudarz Ghanizadeh Hesar
MAMurat Demir Aydin
Murat Demir Aydin
A three-dimensional numerical method for the analysis of Single-lap Adhesive Joints of Aluminum under bending load is presented. Firstly, a meshfree numerical method is investigated for the simulation of the single-lap joint under Four Point Bending load. The element free Galerkin numerical method based on moving least-squares shape functions is used in the meshfree method. The discontinuities at the adhesive segments are approximated with additional degrees of freedom at the nodes. Secondly, we use finite element method by using Ansys program to verify the meshfree method's results and we concluded that the results are consistent in two meshfree and finite element methods.In this meshfree method, we find the displacement in each node for a defined load by using moving least square and element free Galerkin methods, and from these displacements obtainedthe three-dimensional normal and shear stress distributions in the length and depth of the mid-plane of an adhesive layer thickness of 0.12 mm and a lap length of 25 mm, subjected to bending loads at four points. Then calculated Raghava damage criterion for nodes in adhesive segment for two meshfree and finite element methods.

1 January 2022 in International Journal of Exergy
Verified
Journal Article
Closed access
Antonio F. MiguelAntonio F. Miguel
Antonio F. Miguel
DNDevaneyan Solomon Nitesh
Devaneyan Solomon Nitesh
EAEda Uysal Aydın
Eda Uysal Aydın
MAMurat Aydin
Murat Aydin

23 October 2024
Verified
Preprint
Open access
GHGoudarz Ghanizadeh Hesar
Goudarz Ghanizadeh Hesar
MAMurat Demir Aydin
Murat Demir Aydin
In this paper, the effect of tensile loads single-lap adhesive joints of composite in three dimensions is investigated. First, the model of single-lap joint which consists of two composites and FM73 adhesive, it is modeled in three dimensions by using MATLAB software.Then, the model is analyzed analytically by using the meshless method, which is one of the newest numerical methods of analysis. In this regard, the displacement in each node is calculated by using element free Galerkin method, which is one of the numerical methods of the meshless method.Moving least square regression method is used in this analyze. Then the three-dimensional normal and shear stress distributions in the length and depth of the mid-plane of adhesive layer that subjected to tensile load is obtained. To confirm the results of the meshless method, the model was investigated by using the finite element method and stresses that obtained from this method was compared with the meshless method results.The normal and shear stresses were obtained and compared for eight different orientation of carbon/epoxy composite.